I-beam has wide flange, thin web, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.→ compared with the concrete structure, the I-steel structure can increase the service area by %, reduce the self weight of the structure by % - %, and reduce the structural design internal force.Alajuela,In order to improve the corrosion resistance of steel pipe, the general steel pipe (black pipe) is galvanized. The galvanized pipe is divided into hot-dip galvanizing and electric steel zinc. The hot-dip galvanizing layer is thick and the cost of electric galvanizing is low, so there is galvanized pipe. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.Le Tampon,Methods of exerting efficiency in application of C-section steelThe general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold,Alajuela16Mn large diameter longitudinal welded pipe, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.

Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %If the steel pipe is not welded well, that is, if it is not welded, the welding conditions of steel mesh skeleton composite pipe shall be provided.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical,AlajuelaAlloy tube, physical and chemical properties through heat treatment to obtain different service properties.production,The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.It is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components, ladders, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.Main uses: as a finished material, flat steel can be used to make hoop iron, tools and mechanical parts, tractors railway transportation and other machinery.

Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, siliconizing and so on are commonly used in production.investment, Remove defective pipes within the allowable length.Longitudinal welded pipe has the advantages of simple production and processing technology, high production efficiency, low cost and rapid development trend. The compressive strength of spiral welded pipe is generally higher than that of straight welded pipe. Narrow blank can be used to produce welded pipe with large pipe diameter, and blank with the same total width can also be used to produce welded pipe with different pipe diameter. However, compared with the straight seam pipe with the same length, the welding length is increased by ~ , and the production rate is low.I-beamAlajuela,Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe improve plastic deformation quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Stages needing attention in the production and manufacture of alloy tubes The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.