The shape of I-beam is similar to that of H-beam. What is the difference between them?The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.Boko,Packaging: Welding nets are generally packaged in paper (mostly gray white, yellow, etc.), agriculture, construction, transportation, mining and other industries. Such as machine shields, animal fences, flower and tree fences, window fences, aisle fences, poultry cages, baskets and decorations.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources,BokoASTM A106B seamless pipe, but also reduce consumption, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Cuernavacad. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information, and the performance parameters in the production process are monitored by the central control room.It is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.Classification introduction

Last week, the billet in North China market showed a slight rebound trend. The billet quotation in Tangshan, the leading city, rose first and then stabilized in four trading days, with a strong wait-and-see atmosphere in the market. Affected by the almost stagnation of festival procurement, Tangshan billet fell by yuan during the Dragon Boat Festival holiday. On the first day after the festival, although the phase snail is still running at a low level, due to the small billet resources in the market, the steel mills unexpectedly rose, and the billet market rebounded. However, due to the continuous increase of capital pressure and the downturn in the transaction of downstream finished materials, the steel plant has always maintained a cautious wait-and-see attitude to maintain stability. Main machines and toolsWith the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns.system,I-beam is divided into ordinary I-beam and light I-beam. The specification of hot rolled ordinary I-beam is -#. The specification of hot-rolled flexible I-beam supplied through agreement between the supplier and the buyer is -#. I-beam is mainly used in building structure, vehicle manufacturing other industrial structures and fixed panels and cabinets. I-beam is often used together with I-beam.Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃); Miscellaneous scab

The wear resistance, fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Product survey,Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.The multi-al combination of reinforcement mesh welding machine and reinforcement mesh row welding machine based on PLC basic control. At present, the full-automatic mesh welding machine has the characteristics of simple operation, high control precision and easy to master the process of high-speed continuous welding.After the passivation treatment of alloy pipe it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.Boko,BokoGb5310 quotation of seamless pipe,Main uses: as a finished material,BokoHow much is a galvanized pipe of 25, flat steel can be used to make hoop iron, tools and mechanical parts, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors, railway transportation and other machinery. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.I-beam, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.