Some customers want to take a lighter to light the SPC floor to see if it can burn. If it burns, it is not fire safety, and if it doesn&#;t burn, it is flame retardant.In fact the national regulations on the flame retardant grade of PVC latch floor meet the B Standard, and the flame retardant raw materials are listed as class a fire safety according to the national standard, such as marble, wall tiles, etc.The technology of Class B flame retardant grade includes mm diameter cotton wool, sprinkled with ethanol, and placed on the PVC latch floor for natural ignition. After the cotton wool is burned, accurately measure the diameter of the burned PVC latch floor impression. If it is less than mm, it is Class B flame retardant grade.Instead of watching it burn.qualityHaldimandCounty,HaldimandCountyOutdoor wooden floor, Check the ground humidity. Wear resistance, wear resistance grade t.Karnabat,Defects: small blisters can not be repaired after damage, and the upper foot is poor. See: whether the thickness of the ground lacquer cloth is full, whether the foaming layer, printing layer and wear-resistant layer of the bottom layer are layered, whether there is the bottom layer, whether the thickness of the bottom layer is like a cicada wing, and whether the back of the ground lacquer cloth is black.Mute, that is, add cork cushion or other cushion similar to cork on the back of the floor.After using the cork floor mat, the noise of stepping on the floor can be reduced by more than dB (quoted from the data of the cork floor mat factory), which can increase the foot feeling, sound absorption and sound insulation.This plays a positive role in improving the comfort of laminate flooring.It is also a direction for the future development of laminate flooring.

Rich colors and patternsSecond the price is high and the cost performance is not high. Compared with the reinforced composite floor and double-layer composite floor, the price is more expensive;The joint of the floor adopts the form of latch, which controls the vertical displacement of the floor and the horizontal displacement of the floor;The original tenon and groove type, which is often called tongue and groove floor, can only control the vertical displacement of the floor.No matter how early the wooden floor plate is, there is no tenon and groove at the joint, and the displacement in any aspect can not be controlled. Therefore, the floor plate often tilts up and stumbles when walking which is inconvenient.Application process,In addition, pay attention to whether there are sawdust and stratification on the cutting surface of the plate and whether there are sawdust and stratification on the cutting surface of the solid wood floor.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of : leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Secondly, good reliability, moisture-proof,HaldimandCountyWaterproof material, good management methods, rich and colorful color and pattern design types, and large price range.Project scope, Beautiful and diverse colors, seamless splicing construction, convenient and fast installationLook at the color.The third is color.Some customers are very strict about the color of the floor and must maintain the same color difference.But this provision is unscientific.Because the wood is affected by the sun, raw material parts, growth and development parts and lower sawing points,Ground lacquer cloth greenWhen choosing wood flooring in , customers attach great importance to quality.Although the solid wood floor is good,HaldimandCountyHow much is the price of waterproof board, the maintenance is very complicated.In , all stores released high wear-resistant solid wood flooring.It is said that this kind of floor not only has the characteristics of high wear resistance and general solid wood floor, but also has strong coating adhesion, high definition, good corrosion resistance, strong waterproof, not easy to crack and paint.Chamfering rolling paint: a processing technology, and then applies paint to cover the color of the substrate, so that the edge color has a sense of hierarchy, which is similar to the solid wood floor, so it is deeply loved by the majority of consumers.After the chamfered and painted board is paved, there is a very shallow small seam on the upper edge between the board and the board, which is easy to accumulate dust and inconvenient to clean.There is no such problem for boards without chamfering.