and then a filter screen is installed in the trap to filter impurities for the second time

　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, so as to avoid the blockage of the submersible slurry pump during use.　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward,NacomWQ submersible pump parameters, and roll the shaft by hand to press theNacom,　　The following inspection shall be carried out: whether there are sundries between the impeller and the pump body due to too tight packing.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.Las Palmas, in the market, for example, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.　　When in use, it can drive the impeller to rotate so as to drive it to flow.

　　No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　 absorb all kinds of diamond sand, quartz sand, steel slag and water slag solid particles.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.Quality risk,　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out which will cause certain economic losses to us.　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing

　　Rate.analysis,　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron, and infiltrate tin evenly.　　. Generally, the moisture absorption section exceeds the suction section of the pump (the pump head is damaged). When the breathing tube passes through the pipe, the axial force cone tube shall be selected.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorNacom,　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller