In many construction sites, we use this kind of welding for priming, which can effectively ensure its quality and has certain construction difficulties. Therefore, careful and skilled welders should be selected for this work.When water-soluble paper is used to block the ventilation, due to the ventilation from the weld center, the ventilation pipe shall be pulled out quickly at the later sealing link, and the residual argon inside shall be used for protection, so as to quickly finish the bottom and seal the mouth.Wetteren,(II) The price of steel has been running at a low level. From June to June , the overall performance of the domestic steel market was depressed. With the substantial release of crude steel production capacity, the market supply and demand fell into an imbalance, and the steel price entered the downward channel, which has been weak for more than four months. As of June , , the steel price index fell to . points, lower than the first points. The prices of eight steel varieties mainly counted by the iron and steel industry association were higher than at the beginning of the year different degrees Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl% and Ni% which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%, and the single-phase austenite structure is obtained by the combination of Cr and Ni.Vinh Long,WetterenWatch stainless steel mesh belt,Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm; D - Nominal outer diameter of steel pipe, mm.;- Ferromagnetism due to m transformation shall be considered in use (such as in instrument parts).The petrochemical industry, including the chemical fertilizer industry has a great demand for stainless steel pipes. Stainless steel pipes are mainly used in this industry, including, , l, etc., material transmission pipes heat exchanger pipes, etc.

The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.Hot dip galvanized sheet hot dip galvanized sheet, which immerses the sheet into the molten zinc bath to make its surface adhere to a layer of zinc. It is mainly produced by continuous galvanizing process, that is, the rolled steel plate is continuously immersed in the zinc melting bath to make galvanized steel plate. Liaocheng Suntory stainless steel plate weighing method: stainless steel plate: thickness (mm) x width (m) x Length (m) x density stainless steel plate: thickness (mm) x width (m) x Length (m) x density stainless steel plate: thickness (mm) x width (m) x Length (m) x density stainless steel basic weight (density)The back is blocked with blocking plate for ventilation protection; Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection; Use flux cored wire for backing TIG welding.Affordable price, Series & mdash; Heat resistant chromium alloy steel.Refining and transportation industries are in great demand. Secondly, geological drilling, chemical industry, construction industry machinery industry, aircraft and automobile manufacturing, boiler, medical equipment, furniture and bicycle manufacturing also need a large number of various steel pipes. With the development of new technologies such as atomic energy, rocket, missile and aerospace industry, which was consumed and used at the end of the s, is a rebirth group emerging in today's pipe range. It has been widely used in the construction of water supply and direct drinking water pipelines. Stainless steel pipe is durable and has been recognized by the engineering community, and relevant parties are starting from reducing wall thickness and money, so as to facilitate further implementation. In order to promote stainless steel pipe, since the s, China has started to reduce wall thickness and cost; High diameter to wall ratio and high precision & rdquo; The technical effect of stainless steel pipe makes the stainless steel pipe lose its application and expand quickly. There are various connection modes of stainless steel pipes. The rare types of pipe fittings include contraction type, compression type, union type, push type, push thread type, socket welding type, union flange connection,Wetteren304 sanitary stainless steel pipe, welding type and derivative series connection mode combining welding with traditional connection. These connection methods have different application ranges according to their principles, but most of them are convenient, firm and reliable. The sealing ring or gasket materials used for connection are mostly silicone rubber, nitrile rubber and EPDM that meet the requirements of national specifications, which eliminates the worries of users. In the construction of water supply pipe system, due to the glorious history of galvanized steel pipe, all kinds of new plastic pipes and composite pipes have been lost and developed rapidly, but they are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. In direct drinking water, stainless steel pipe system is undoubtedly one of the best. At present, hotels and public places at the international level have been equipped or are equipped with direct drinking water pipelines. In many cases, especially the stainless steel pipe with wall thickness of only . ~ mm has the characteristics of safety, reliability, sanitation, environmental protection, economy and applicability in high-quality drinking water system, hot water system and water supply system that puts safety and sanitation first. It has been proved by engineering theories at home and abroad that it is not only one of the new, energy-saving and environmental protection pipes with good comprehensive function of water supply, but also a very competitive water supply pipe, which will play an unparalleled role in improving water quality and improving people's living standard.

Model & mdash; Except that the risk of weld corrosion of the material is reduced due to the addition of titanium, other properties are similar. Stainless steel decorative pipe, stainless steel pipe, series stainless steel pipe & mdash; Ferritic and martensitic stainless steel model & mdash; Good heat resistance, weak corrosion resistance, % Cr, % Ni.Quotation sheet,High frequency welding high frequency welding: with relatively high power supply, it can reach a higher welding speed for steel pipes with different materials, outer diameter and wall thickness. Compared with argon arc welding, it is more than ten times its high welding speed. Therefore, stainless steel pipes for common use have a higher consumption rate. Due to the high speed of high frequency welding, it is difficult to remove burrs in welded pipes. At present, high frequency welding Welded stainless steel pipe can not be borne by chemical and nuclear industries, which is also one of the reasons.Check whether the sealing ring of pipe fittings is complete and clean and whether the placement position is correct. If there is dirt, it must be cleaned up. If the sealing ring is damaged, the burr shall be removed to avoid cutting the sealing ring.WetterenDeburring: after the pipe is cut off,WetterenQuotation of stainless steel pipe, the burr shall be removed to avoid cutting the sealing ring.According to the purpose it can be divided into oil well pipe (casing, oil pipe and drill pipe), pipeline pipe, boiler pipe, mechanical structure pipe, hydraulic prop pipe, gas cylinder pipe, geological pipe, petroleum cracking pipe) and marine pipe.At present, stainless steel backing is divided into two processes: back argon filling and non argon filling. Back argon filling protection can be divided into solid wire + TIG process and solid wire + TIG + water-soluble paper process; The back non argon filling protection is also divided into flux cored wire backing welding and welding rod (flux coated wire) backing TIG welding.