First screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve　　Submersible slurry pumps are mainly used in mining, metallurgy,KzaletepecFire deep well pump, coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example,KzaletepecVertical non clogging sewage pump, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump bladeKzaletepec,　　The main and feature of self-priming pump is self-priming capacity. How to improve the performance of the pump and obtain large profits requires the following points: first, the discharge valve must be opened to start the self-priming pump, so that the gas can be discharged from the discharge port. Secondly, there should be enough liquid in the cavity of the self-priming pump, otherwise it will not　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy,　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry　　Flexibility. The equipment has advanced structure, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles strong sewage discharge capacity, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.

　　With water, you can start working.　　 number of lifting pipes　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way canHonest management,　　 Cutting blades can be selected to cut some large block solid substances into pieces during use,　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.

　　What is the solution to this situation?reform,　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　 Pipeline single-stage single suction chemical pump. Pipeline pump used for transporting chemical corrosive liquid in textile, pharmaceutical, health, food, chemical, petroleum, oil refining and other industries, with the service temperature not higher than ° C. It is an ideal product to replace the traditional chemical pump.　　 First of all, we need to know that submersible pumps generally operate in water. In fact most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps mayKzaletepec,　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers,KzaletepecSelf priming non clogging sewage pump, middle sections and guide vanes at other levels in the same way until the submerged slag slurry　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water