It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, water pumps and generators　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition,Vinustiano kalanzaScrew deep well pump, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pumpVinustiano kalanza,　　The discharge side of the pump must be equipped with a valve (ball valve or stop valve, etc.) and a check valve. The valve is used to regulate the operating point of the pump. The check valve can prevent the pump from reversing when the liquid flows back (the long shaft deep well pumps produced by our company are equipped with anti reversing check devices) and prevent the pump from being hit by water hammer　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.Quba　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should choose

　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore, in fact, it is mainly　　 hydrogen sulfide gas content mg/l　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pumpInspection environment,　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more

　　Second, the power used is not matched,Vinustiano kalanzaWear resistant slurry pump, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so ICreate brilliance,　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　 Requirements for the process pretreatment unit for the normal operation of the screw pump the stator of the screw pump is generally made of rubber and the rotor is made of stainless steel. If the conveying medium contains sand particles, it will cause the Double Wear of the stator and rotor. Due to the requirements of the processing technology and materials, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact this measurement is not very accurate.Vinustiano kalanza,　　About %), and motor power p=i × U indicates that high power and current will increase.　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way,Vinustiano kalanzaDouble suction slurry pump, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and