I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Because all parts of I-beam are arranged at right angles,SeattleHow much is a 32 welded pipe, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.SeattleGalvanized pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, power engineering, power plant agricultural and chemical machinery, automobile chassis, airport, highway railing,Seattle42CrMo seamless pipe factory, pressure vessel, oil storage tank, bridge, power plant equipment, Hoisting and transportation machinery and other welded structural parts with high load.→ wide flange and large lateral stiffness. Strong bending resistance.Austria,Classification introductionAt present, there is still a big gap in the production technology of C-section steel between China and foreign countries.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web,SeattleHow much is No. 14 I-beam per ton, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.

The utility model has the advantages that the axial force of the roll is small, the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body, and more passes can be matched under the condition of a certain length of the roll body.Recently, the price of zinc has been falling continuously. The key reason lies in the soft skin of galvanized pipe consumption and the slow start of production and marketing rate of manufacturing industries in the middle and lower reaches after the Spring Festival. The disadvantage of zinc price has long been far beyond the level of cyclical factors. The main performance of no prosperity in the hot season is whether the market situation in the off peak season will become a more worried problem in the galvanized pipe sales market.→ compared with the concrete structure, the I-steel structure can increase the service area by %, reduce the self weight of the structure by % - % and reduce the structural design internal force.Safety production,What should we pay attention to in the production of alloy pipeThe key purpose of grinding and polishing alloy pipe is to moisten the surface and the relevant limit accuracy or appearance change is not easy to change.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.

In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.Welcome calls , curtain wall engineering, mechanical equipment and vehicle manufacturing.Cold.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Seattle,→ the two surfaces of the flange are parallel to each other, making it easy to connect