Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time,Wokavisk12Cr2MoWVTiB alloy pipe,WokaviskHow much is the price of galvanized pipe, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.Heating surface pipes, economizers superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Wokavisk,The two ends of the steel produced by the seamless pipe manufacturer shall be cut into right angles,WokaviskHow much is the I-beam for a ton, and the burrs on the surface shall be removed, which is the raw material used by the seamless pipe manufacturer. The embryo prototube embryo needs to be cut by a cutting machine to form an embryo material with a length of about one meter, which is sent to the furnace for heating through the conveyor belt. The billet is sent to the furnace. After internal heating, the temperature is about degrees, and the fuel used is often ethyne. Temperature control in the furnace is a very key factor. Frame line crackKifri,I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, it has good versatility and combination, eliminate structural defects, reduce strength, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality. Construction preparationBecause the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.Test method,Some applications of I-beam:Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.

It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact, this cognition is wrong. H-beam and I-beam are different in shape!supply, when the steel structure changes during heat treatment, that is, austenite transforms into martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. Due to the change of tissue stress the tensile stress on the surface and the compressive stress in the heart are just opposite to the thermal stress. The magnitude of microstructure stress is related to the cooling rate, shape and chemical composition of martensitic transformation zone materials. Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Wokavisk,Defects of alloy pipe and solutions:The system is mainly composed of control box, finishing roller, pre leveling unit, finishing unit and straightening unit.The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm expressed as No. ~ No., cross rolling pass system and mixed pass system. In addition and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system