Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment and the current will slowly increase during use. Well, we should choose　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.Burrell,　　 during operation, the deep well pump shall rotate smoothly without vibration and abnormal sound. Observe whether there is obvious fluctuation in the motor running current and line voltage before and after startup. The change of water level in the well shall be observed frequently. The motor must not be exposed to the water surface or sink into the sludge to avoid affecting the power supply　　A large amount of lubricating oil is stored.Rostov on the don,　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?

　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I　　Automatic pump failure: cause: A. whether the frequency converter has abnormal symbols; b. Whether the actual pressure is higher than the set pressure.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.Quality risk,　　 There may also be mechanical failure of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height,BurrellRubber lining submerged slurry pump, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,

　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves so as to avoid peopleAdministration,BurrellWater well pipeline pump,　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　If you want to know how the slurry pump is classified, you must first understand what the slurry pump is: conceptually, it is a machine that increases the medium energy of the solid-liquid mixture through the centrifugal force generated by the rotation of the impeller, and a device that converts the electric energy into the kinetic energy and potential energy of the medium. and　　The whole packing body, including the packing gland,BurrellFire deep well pump, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vaneBurrell,　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.