After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.Somoto ,　　 transmission device type (gearbox transmission, flat belt transmission, V-belt transmission)　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline,Somoto Horizontal wear-resistant slurry pump, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing bodyIztapalapa,　　After meters, the sealing of the equipment can not bear the water pressure at this depth.　　Under the action of auxiliary devices, it can transport the slurry, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　Be sure to choose a pump that is more suitable for use.

　　The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, which makes it difficult to distinguish. Today we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two　　Conduct a comprehensive preventive maintenance once a year, including: replace all O-ring seals; Check the bearing wear and add new grease; Check the wear condition of the mechanical seal to determine whether it needs to be replaced; Check the wear of the impeller and the seal between the impeller and the pump body　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.Interpretation and observation,　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　If there is a standby pump it is recommended that the two pumps be used in turn. When the equipment is in use,Somoto Submersible slurry pump, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.

　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal useInspection requirements,　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.　　The main shaft of the water pump is bent or the main shaft of the water pump and the motor is not concentric or parallel.　　Reasonable.Somoto , and conduct hydrostatic test if necessary.　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using