Darbus Second floor cargo elevatorSkills
2024-04-20 00:26:16Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Darbus ,Darbus Freight elevator lifting, the pressure of the lifting platform will test the weight of the cargo. If it is overloaded, the general lifting platform will prompt. This is the role of protection, so now the lifting platform is pressed. pressurizer. Hydraulic machinery should remind everyone to pay attention to the following points: The precautions for the use of small lifting platforms are to look at the pressure. Their load capacity is very poor, and the size is small. When using it, it will It caused structural damage to the lifting platform, which we have said many times before.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.Huamachuco,After the goods are transported,Darbus Chain guide rail type cargo elevator, clean up the debris on the platform.The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.
What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.The lifting height is stable, which can meet the smooth lifting of large-tonnage cargo. The hydraulic lifting stage is equipped with an anti-attachment and overload protection hydraulic system to ensure operation. It is a long-term operating freight elevator factory. Welcome to consult.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Where to sell API,Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands it may cause lifting failure in light cases, the platform is level with the ground, does not occupy the ground space and does not affect the passageway.
The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Sincere service,Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.Drain the hydraulic oil of the hydraulic lift and discard it. Tighten the joint to take out the oil filter. After cleaning, clean it with compressed air, then put it back into the oil tank, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Darbus ,Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.The last thing to note is that, compared with the lifting platforms in some places, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail,Darbus Fixed lifting hydraulic cargo elevator, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.