On October , according to the Economic and Information Commission oong Province, at the end of September , Shandong Province had resolved the overcapacity of million tons of pig iron and million tons of crude steel, and all the de capacity equipment had been shut down and withdrawn. On October , the Development and Reform Commission of Handan City released the Plan for Handan City to Eliminate Excess Iron and Steel Capacity. Statistics show that the iron making capacity of Handan in was million tons and the steel making capacity was million tons.Disadvantages: Due to loose tissue and high pressure resistance, the pipe is only used to produce small air conditioning copper rods.Nizhny NovgorodWater with low PH value causes corrosion.The copper bar market declined steadily this week, with a decline of - yuan. Due to low pig iron inventory, some steel mills in Jiangxi have resumed purchasing recently, but the purchasing volume is not large. The purchase price of pig iron in Yunnan steel plants was slightly increased to ensure the purchase volume due to the low purchase price of pig iron in the early stage. Recently, the steel market has been in shock and adjustment, and the merchants are unstable. Steel mills in Hebei, Tianjin and other regions have stopped producing pig iron for steelmaking. Now, it is mainly expected to make inquiries. However, due to the lower price of raw materials, the price of iron mills has been lowered.San Isidro de Curuguaty,Generally, oxygen aylene is used as the gas source and LPG welding tool is used for heating. The torch of the welding tool shall face the joint and then continuously heat the whole joint. This will avoid excessive local heating.The main force of iron ore futures closed at in The closing price of the day today was the same as that of the previous trading day, including * * * * , * * * , settlement price , trading volume , and position volume . The intraday tradg volume decreased by compared with the previous trading day, and the position volume decreased by compared with the previous trading day. After six consecutive days of downward adjustment, there was a rebound at the bottom of the session today but it was corrected again later, and the closing was flat.For small diameter pipes, when using filler metal,Nizhny Novgorod1060 aluminum bar, red copper bar and red copper tube: copper is the most widely used and used in the electrical and electronic industries, accounting for more than half of the total consumption. Used for various cables and wires, motors and transformers, switches and printed circuit boards; In the manufacture of machinery and transport vehicles, it is used to manufacture industrial valves and accessories, instruments, sliding bearings, molds, heat exchangers, pumps, etc.

Disadvantages: low output, high production cost and high price. Extrusion copper tube process is a stable and excellent copper tube production method at home and abroad at present. Only the copper tubes produced by this process are more suitable for the field of heating and ventilation, which is the development direction of copper tube industry in the future.The storage and transportation of copper tubes in summer should also be paid attention to when controlling the surface of copper tubes.With the advent of heating season,Nizhny NovgorodRed copper bar, the raw material support of red copper row is weak. Under the influence of heating season and environmental protection production restriction, steel mills in some regions began to implement the production restriction measures for blast furnaces in heating season, and the demand for iron ore was weakened. In addition, the production restriction measures specified in this Notice were implemented.technological innovation,Red copper inventory in key areas has risen continuously, but the total pressure is not big. From the current overall inventory situation of the main distribution centers Wu an, Jiangyin and Lecong, the inventory level remains relatively moderate, and the pressure on the market is relatively small. In Wu an market, according to the data, as of May , the total inventory of medium and thick plates in Wu an was close to tons, increasing by tons on a weekly basis. In late April, it reached tons lower in the year, down tons from the high level after the Spring Festival, and rose for three consecutive weeks. In terms of the ovquantity,Nizhny Novgorod12CR1MOV alloy plate, it should be said to maintain a relatively moderate level.Disadvantages: low output, high production cost and high price. Extrusion copper tube process is a stable and excellent copper tube production method at home and abroad at present. Only the copper tubes produced by this process are more suitable for the field of heating and ventilation, which is the development direction of copper tube industry in the future.Copper tube is also called copper tube nonferrous metal tube. It is a pressed and drawn seamless pipe, characterized by light weight good thermal conductivity, the use of copper tubes is very common. What are the differences between hard copper tubes and soft copper tubes in the use process? What are the differences between the two in terms of specific applications?

When welding high low-temperature strength and corrosion resistance. Because of these excellent properties of copper tubes, just add enough filler metal to fill the capillary gap. Too much filler metal will only form a ball at the bottom of the joint or run into the pipe.Welcome calls ,Among the three production methods of copper tube, the oxidation method is the most. Because as long as the metal copper is oxidized by the anode and the copper ion of the anode is attached to the tube material, the copper tube can be produced. Thisthod is also the most common method to produce copper materials. It has not only been used for a long time, but also has a mature technology, which is to produce copper tubes through oxidation reaction. This production method is the main production method of copper tubes in China.When stacking, reasonable stacking and first in first out shall be achieved.Copper tube is also called copper tube nonferrous metal tube. It is a pressed and drawn seamless pipe, characterized by light weight, good thermal conductivity, high low-temperature strength and corrosion resistance. Because of these excellent properties of copper tubes, the use of copper tubes is very common. What are the differences between hard copper tubes and soft copper tubes in the use process? What are the differences between the two in terms of specific applications?Nizhny Novgorod,The hard copper tube is not artificially treated after being drawn or extruded, the organizational form in the copper tube is full. This kind of copper tube is more likely to crack and is not suitable for bending. Therefore, the hard copper tube is generally straight.The price of pig iron market rose by - yuan this week, and the transaction was fair. With the increase of coke price, the cost of ductile iron in Shanxi, Henan, Liaoning, with the gradual release of downstream demand, the inventory of iron plants is not large, and iron plants have successively raised their prices. There are few iron foundries in Shandong, Jiangsu, Hebei and Shanxi and the inventory remains low. As the coke price rises and the cost increases, the price of iron foundries rises again.It has excellent conductivity, thermal conductivity, ductility and corrosion resistance.