Generally, there are many passivation methods for alloy tubes, the common ones are high temperature passivation or sodium cyanide passivation.Key technical characteristics of alloy pipeRodas, Pipe installation:The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Pereira,Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Key technical characteristics of alloy pipeI-beam,RodasWhat is the outer diameter of welded pipe DN50, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.

Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.The two ends of the steel produced by the seamless pipe manufacturer shall be cut into right angles, and the burrs on the surface shall be removed, which is the raw material used by the seamless pipe manufacturer. The embryo prototube embryo needs to be cut by a cutting machine to form an embryo material with a length of about one meter, which is sent to the furnace for heating through the conveyor belt. The billet is sent to the furnace. After internal heating, the temperature is about degrees, and the fuel used is often ethyne. Temperature control in the furnace is a very key factor.→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection,RodasReinforcement turnover software stand-alone version,→ under the same section load the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.At the same height, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards.Some applications of I-beam:

The side length of I-beam is small and the height is large so it can only bear the force in one direction.install,It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact, this cognition is wrong. H-beam and I-beam are different in shape! Spiral seam submerged arc welded steel pipe for general low-pressure fluid transportation (SY / t- is a submerged arc welded steel pipe for general low-pressure fluid transportation such as water, gas, air and steam, which is made of hot-rolled steel strip coil as pipe blank, often warm spiral forming and double-sided active submerged arc welding or single-sided welding.b. The professional two-sided arc welding processing technology can complete the electric welding at a good position which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration,RodasHow much is a welded pipe meal, and it is very easy to manipulate the welding quality.Rodas,→ I-beam can be processed into T-beam, and honeycomb beam can be combined to form various section forms, which greatly meets the needs of engineering design and manufacturing. Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, easy maintenance, durable economic development and convenient product specification transformation. For example, the production of large diameter must be grooved pipe, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, thick wall and thin alloy steel pipes, and can not exceed the working capacity of thick wall pipes of machinery and equipment. Frame line crack