St. ChristopherLong shaft submerged slurry pump,

　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box loosen the adjusting nuts, and roll the shaft by hand to press theSt. Christopher　　As a display screen, the operation of each fire pump is clear at a glance,St. ChristopherCarbon steel explosion-proof pipeline pump, and the management is very convenient.　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps waterMonte-Plata,　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy　　 Check the suction pipe and bottom valve to see if there is any air leakage source. Remove the silt and other obstructions at the water inlet. Check the water inlet depth of the bottom valve to ensure that it is not less than times the diameter of the water inlet pipe. If it is not enough, deepen the water inlet depth of the bottom valve.　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so IInstallation works,　　As an emerging product, the submersible slurry pump has many advantages, especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, the application of the submersible slurry pump is gradually becoming more and more widespread, and the market recognition is continuously improving, especially meeting the needs of deep-water sand pumping and dredging. At present, the depth can reach meters.　　 First remove the pump from the engine.　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.

　　 There may also be mechanical failure of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps waterInterpretation and observation,　　Commodity.　　 estimated installation depth of pump M　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impellerSt. Christopher,　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant,St. ChristopherCorrosive pipeline pump, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.