XinfuMobile lifting platform scissor fork typeHow to solve the problem
2023-09-28 08:41:03Check if the orientation of the upper and lower limit blocks on the guide rail frame is correctWeekly maintenance: According to the operation instructions,Heavy load capacity: protective plate form: ° Or ° Interchangeable configuration rocker working angle: ° Drive method: hydraulic power unit drive or screw drive.Regularly check all wires and cables for damage. Timely bandage and replace damaged parts.Kontagora,Check the protective cable condition of the cable guide frameWeekly maintenance: According to the operation instructions, ensure that the elevator is inspected and smooth every dayThe lifting stage can provide real-time information on the operation of the entire vehicle, avoiding relying solely on the experience of operators to coordinate with each other and improving the reliability and safety of the system. The definition of safety zone is very important because the lifting stage has a large range of movements, and it must be accurately calculated. The lifting stage has two structurally separate systems, the ground turntable and the high-altitude work bar. However, for various movements on the vehicle,XinfuMobile scissor fork lifting platform, it is also an interconnected system, which needs to consider the priority of operation, system redundancy, racks, rollers and guide rails. If adjusted more carefully, it will be more beneficial for the service life of the elevator.Low failure rate: Due to the use of advanced hydraulic systems and good methods, the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends, it is driven by the pressure generated by its own weight, which greatly saves energy.Monthly maintenance: View weekly inspection itemsWelcome to inquire,Lifting and loweringRegarding the construction elevator with counterweight, check the adjustment and fixation status of the counterweight guide wheel. Check the balancing equipment of the steel wire rope, the crown wheel, and the counterweight steel wire rope bracketEnsure that power cables and electrical circuits are not damaged
The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %.Management Department,XinfuSelf propelled mobile lifting platform,When disassembling the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts, it is necessary to avoid dust during the system oil passage. The disassembled parts must be thoroughly cleaned before opening. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap. After loosening the tank cap, remove any remaining debris from the joint area (do not rinse with water to prevent water from seeping into the tank). Only after confirming cleanliness can the tank cap be opened. When using materials and hammers, materials that do not remove fiber impurities and specialized hammers with rubber attached to the surface should be selected. Hydraulic components and hydraulic hoses should be carefully cleaned,XinfuMobile lifting platform scissor fork type, dried with high-pressure air, and then assembled. Choose a well packaged filter element (the inner packaging is damaged, although the filter element is intact, it may also be unclean). When changing the oil, clean the filter at the same time. Before installing the filter element, and the layout principle is: when the aspect ratio of the component is greater than , two point supports can be used; When the aspect ratio is close to , it is advisable to use or -point support.Check all standard sections and diagonal support connection points. Check the fastening bolts of the gear rack and ensure that the motor cooling wing plate and organization are cleanXinfu,Check the interlocking equipment, up and down travel, and other safety maintenance switches of the cage door and fence doorThe wear rate is fast and due to factors such as processing, assembly, and adjustment of new machine components, the friction surface is rough, the mating surface area is small, and the surface pressure condition is uneven. During the operation of the machine, the concave and convex parts on the surface of the parts are intertwined and rubbed against each other. The metal debris that falls off from the grinding process, in turn, acts as abrasive and continues to participate in friction, further accelerating the wear of the mating surface of the parts. Therefore, during the running-in period, it is easy to cause wear on components (especially the mating surface), if overloaded, it may cause damage to the components and lead to early failures.Check the safety interlocking equipment of the first cut door of the hanging cage