The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.After chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, resulting in electrode potential difference, so the steel surface treatment requirements are very high.Candlestick,Today, with the development of the world, all fields are coming rapidly, which makes the demand for square tube higher and higher,CandlestickFire galvanized pipe, and the requirements of customers for square tube higher and higher. Now we are studying a new square tube. The following mainly introduces the performance of square tube in tensile strength.The reason why the surface of fake and shoddy materials is easy to crack is that its blank is adobe with many air holes. During the cooling process, the adobe has cracks due to the action of thermal stress, and there are cracks after rolling.Bhilai,A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.The second is the pickling of the square pipe. Both chemical and electrolytic methods are used when pickling the square pipe. These two methods can remove the oxide skin of the square pipe.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.

The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting manual and mechanical derusting can be adopted, but the derusting quality level must be reached.Low alloy steel is divided into q Mn, Q, St-, etc.Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!device managementThe second is the pickling of the square pipe. Both chemical and electrolytic methods are used when pickling the square pipe. These two methods can remove the oxide skin of the square pipe.For transportation: water supply, drainage, sewage treatment engineering, mud transportation, marine water transportation.Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.

The reason why it is divided into two types is that chemical cleaning can only clean the surface very thoroughly, and it is difficult to achieve the desired results in some fine cracks.query,Generally speaking, square pipe welding has a process: ignition,CandlestickWelding video of galvanized square pipe, pressurization and thermal insulation.Process flow of square tube drawing: because the size of the die hole of the square tube drawing is smaller than the outer diameter of the tube in front of the drawing, in order to make the front end of the square tube pass through the die hole smoothly, so that the clamp jaw of the drawing trolley can the head of the square tube, it is necessary to sharpen the head of the square tube before drawing. Therefore, the end of the square tube with a fixed length should be heated in the slit heating furnace, It is generally ~ mm, and the heating temperature is between ~ ℃ according to different wall thickness. Then use ~ kg air hammer to sharpen and grind the head of the square pipe. Generally, the square pipe with diameter less than mm can be sharpened by rotary forging hammer or roll forging machine.Ferroalloy is an alloy composed of iron and silicon, manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.Candlestick,Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.