The strength, plasticity and hardness discussed above in fatigue QB are the indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.It is the process of drawing the die hole of the rolled metal blank (shape, pipe, product, etc.) into a section to reduce the length and increase. It is mostly used for cold processing.Komitanchilo,Square tube industry plays an important role in production and construction. Square pipe is a steel pipe made of a whole piece of metal without joints on the surface, which is called square pipe.Qb square tube, qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same, but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.Naxxar,Viewing color: the color of the cold galvanized square tube is yellowish green cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.

Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.General square pipes are stacked outdoors, and most of them are buried underground when in use, so they are easy to corrode and rust. In order to ensure the smooth flow of the pipeline, square pipes must have strong corrosion resistance. Once the pipeline is corroded, it will cause oil and gas leakage,Komitanchilo37 galvanized square pipe, which will not only interrupt transportation, but also pollute the environment,KomitanchiloHow much is a galvanized square tube, and may even lead to fire and cause harm.The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.consumption,In this period, the technology of continuous rolling pipe was not mature.Superior square tubular steel (both P and s ≤ .%)The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.

Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.wholesalerSquare tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including,Komitanchilo40 galvanized pipe, pipe blank cutting, saw blade return opening device, pipe blank discharge, head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.Square tubes can be degreased with organic solvents (vinyl chloride, vinyl chloride, carbon chloride industrial solvents, benzene, acetone, etc.), concentrated or alkaline solution. Industrial vinyl chloride is suitable for degreasing metal parts; Industrial chlorinated carbon is suitable for degreasing ferrous metal and non-metallic parts; Vinyl chloride is suitable for degreasing metal parts and non-ferrous metal parts; The industrial concentration shall not be less than %, which is suitable for manual scrubbing of the inner surface of the container with low degreasing requirements; % concentrated, suitable for degreasing some pipe fittings and porcelain rings of concentrated device.B. spring steel C. bearing steel tool steel: A. carbon tool steel; b. Alloy tool steel; c. High speed tool steel.Komitanchilo,Reinforcing phases such as reinforcing particles, if necessary, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.