Whether the pump is evacuated or overflowed, etc., and handle it at any time.　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.San Jose,　　Pumps, self-priming pumps, sewage pumps, it belongs to a portable workstation, which can be brought wherever it is needed,　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly

　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry　　 the pipeline shall be designed as a circulating circuit to minimize turning, prevent microbial breeding and reduce water quality.　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.The cheapest,San JoseQuotation slurry pump,　　In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance,San JoseHorizontal wear-resistant slurry pump, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　The application of pumps involves all aspects of work and production,San JoseISG single stage vertical pipeline pump, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two

　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor the motor is only in local placesRespect for customers,　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　 Shaft seal part auxiliary impeller shaft seal: through the impeller action of a reverse centrifugal force, prevent the slurry from leaking out. When the positive pressure at the inlet of the pump is not greater than % of the pressure at the outlet of the pump, the single-stage pump or the first stage pump in series can adopt the auxiliary impeller shaft seal, and the auxiliary blade shaft seal is not required　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumpingSan Jose,　　 repair and level the welding part of the submersible slurry pump with a file clean the part to be bound with alcohol again and wipe it dry.　　Rate loss, you can refer to the following reasons.

so shaft power = effective power + lost power.　　It will burn out. If there is a heating problem in use