Because the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large,Villa Nicholas RomeroGalvanized strip round pipe factory, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending,Due to the interaction between chromium and carbon in martensitic chromium nickel square tube, stable R phase region and stable a + R phase region are formed at high temperature. The increase of carbon content can expand the R-phase region, but the dissolution limit of carbon decreases with the increase of chromium content. The addition of nickel to martensitic chromium nickel square tube solves the problem that the hardness of steel is sacrificed to improve the corrosion resistance of martensitic square tube. However, the nickel content is not easy to be too high, otherwise the square tube will become austenite square tube due to nickel expanding austenite phase zone and reducing MS temperature, so as to completely lose the quenching ability.Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.Iquitos,Because the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions,Villa Nicholas RomeroWhere is galvanized square tube cheap, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, it can reflect that the square tube is good. On the contrary, if the surface is not goodStrength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets,Villa Nicholas RomeroGalvanized square steel pipe, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is the warehouse with roof, enclosure, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation loading and unloading and shall not be damaged, The storage period of materials can be extended the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, if the surface is not good

Strength QB square strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, improve material rate and improve product quality. Seamless pipe is rolled in the annular pass composed of variable cross-section circular hole groove and fixed conical plug. Cold drawing is usually carried out on single chain or double chain cold drawing machine. This method is to put the heated pipe blank in a closed cylinder, and the perforated rod and rod move to extrude the part from the smaller die hole. This method can produce steel pipe with smaller diameter.At the same time, the heating temperature and heating time will also have a great impact on the performance of square tube. The heating of square tube blank is the key process to ensure that the square tube blank has enough plasticity and complete the smooth perforation. If the heating temperature is too high or the heating time is too long, the billet of the square tube will be burned and decarburized, and even the chemical composition of the square tube will be unqualified (unqualified carbon content), which is easy to cause batch quality problems and seriously affect the product qualification rate.Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.analysis,Functional index analysis of qb square tube - mechanical function of plastic square tube. Solid bending, is to compact the bending. During real bending, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.Reinforcing phases such as reinforcing particles, short fibers and whiskers can be added to the solder to form composites.Mechanical engineering, power plants, agricultural and chemical machinery, glass curtain walls, automobile chassis, boiler construction, highway railings, housing construction, pressure vessels, oil storage tanks, bridges power station equipment, heavy transportation machinery and other welded structural parts with high load, etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes, seamless square tubes and qb square tubes.

Stage ( & mdash; )Installation materials,After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.Tensile test is to form seamless qb into a sample, pull the sample to fracture on the tensile testing machine, and then measure one or more mechanical properties. Usually, only tensile strength, yield strength, elongation after fracture and reduction of area are measured.After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.Villa Nicholas Romero,Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, open square pipe, special-shaped square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe, large-diameter qb square pipe purpose classification square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tool equipment, machinery industry, chemical industry, steel structure, automobile, steel beam and column, special purpose, large-diameter qb square tube wall thickness classification, large-diameter qb square tube according to wall thickness Classification & mdash& mdash; Super large diameter qb square pipe, large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe, also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe, code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm, except for the wall thickness of corner and welding joint area.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.