MoreliaTop ten brands of laminate flooring,

Fifth, the total thickness of the floor is about , cm, which is also related to his total price.The density of laminate floor substrate (high density fiberboard) shall be .-. g / cm, and it is not appropriate to have too low or too high density.Morelia,After the wax on the ground has set, scrape off the protruding part along the ground with a plastic ruler or credit card. Never soak the floor with water during use. If there is an accident, mop the floor with a dry mop in time.Babahoyo, After days, maggots appeared on the floor.This problem is because the floor contains a lot of impurities.UV layer: the coating formed after UV oil is cured with curing agent, which can prevent the volatilization of chemicals in the plate by UV.[]Some customers want to take a lighter to light the SPC floor to see if it can burn. If it burns, it is not fire safety, and if it doesn&#;t burn, it is flame retardant.In fact, the national regulations on the flame retardant grade of PVC latch floor meet the B Standard, and the flame retardant raw materials are listed as class a fire safety according to the national standard, such as marble, wall tiles etc.The technology of Class B flame retardant grade includes mm diameter cotton wool, sprinkled with ethanol, and placed on the PVC latch floor for natural ignition. After the cotton wool is burned, accurately measure the diameter of the burned PVC latch floor impression. If it is less than mm, it is Class B flame retardant grade.Instead of watching it burn.

Fourth, it is mainly the veneer thickness (decorative board thickness). The multi-layer solid wood floor has ,-, and the new three-layer solid wood floor has , to ,MoreliaSPC floor production, mm.In another case, the scar is deep, which can be supplemented with solid recovery wax, colored with paint repair pen, and then polished.Third, look.Affordable price,SPC floor is an economical floor material. Consumers can enjoy the texture of wood grain or stone grain in use without being bothered by noise.According to the requirements of consumers for sound insulation, also known as floor leather (not PVC plastic floor), is a kind of paving material. It belongs to rubber plastic products. It is one of the indispensable floor materials for the decoration of power distribution room,MoreliaHow to stick the floor leather, substation and communication room. The thickness is -mm. Other thicknesses can be made according to the needs of users. The wear-resistant layer is generally less than or equal to .mm.The choice of lacquer cloth products shall be selected according to the suitability of the site.For example, the size of the product is determined according to the space of the house and the size of the place of use.At the same time, pay attention to the different places of use, and the selected patterns should also be different.For example, in places that need to be kept clean, you can&#;t choose products with convex effect;In solemn places, it is not suitable to choose products with bright colors and messy.The width of coiled floor paint cloth is mm, mm and mm;The total thickness (referring to the base material, intermediate layer and surface wear-resistant layer) is divided into mm and mm;The length of each roll of floor leather is m and m.Other specifications and dimensions can be determined by the supplier and the buyer through negotiation.Because of the requirements of production each roll of floor paint cloth is divided into several sections (the patterns between each two sections are misplaced), so the length of the small section of a roll of floor paint cloth with sections shall be indicated, and the length of the roll of floor paint cloth shall be increased by at least cm (i.e. not less than two complete patterns).Generally, there can only be one section for high-quality products and the number of sections of each volume of first-class products and qualified products shall not exceed ;The length of each section of first-class products shall not be less than m, and the length of each section of qualified products shall not be less than m.When inspecting the appearance quality of floor paint cloth leather, it should be visually inspected obliquely under the scattered sunlight or fluorescent lamp with the illuminance of ( ± LX and LM away from the tested sample.First, observe whether there are cracks, fractures and delaminations on the surface of the floor leather. If so, it can be determined that the floor leather is unqualified.The second step is to observe whether there are wrinkle marks bubble pollution points and pattern deformation. What cannot be observed are excellent products and first-class products;If it is slight but not obvious, it is deemed as qualified. Go back to the third step to observe whether there are missing patterns on the surface of the floor leather and whether there are defects of the transparent wear-resistant film on the surface. If there is no, it is the first-class product and the first-class product. If there is slight missing or lack of film, it is the qualified product, otherwise it is the unqualified product.Finally, carefully check whether there is deviation during multi-color overprint on the surface, whether there are color differences in different parts, whether the superior products are uneven and if there are the above two defects, the first-class products are those with but not obvious, and the products with obvious above defects but do not affect the overall beauty are determined as qualified products.Finally, based on the above judgment, the appearance quality of ground lacquer cloth is determined.The plastic coil floor paint cloth shall roll the wear-resistant layer outward on the pipe core and shall be externally packaged.The product name, manufacturer name, product mark, grade, batch number, quality and length shall be marked at the obvious place of each package.In addition to the above three items that can be directly judged by the senses, attention should also be paid to the physical properties when purchasing floor leather to ensure its service life.From to , Chinese traditional pure solid wood flooring and new solid wood flooring, which means three-layer and double-layer solid wood, have been surging in an undercurrent.In recent years, new solid wood has maintained a high annual growth rate of more than %.Under the economic development layout from to , the upgrading of solid wood flooring category caused by new solid wood will become an important driving force to promote the consumption boom of home decorative flooring.The world financial storm has an impact on China&#;s wood flooring industry chain, but it is not rampant, only lack of confidence in the market.The operation track of the development of market economy has been advancing in the cycle system of wave soldering and wave trough. The flooring industry is depressed and it is not easy to hold it for a long time. China has a strong foreign demand market, and the demand of China&#;s home building materials market is still very large.The density of laminate floor substrate (high density fiberboard) shall be .-. g / cm, which is super wear-resistant.Therefore, stone plastic flooring is becoming more and more popular in hospitals, schools, shopping malls, supermarkets, Moisture proof, no deformation in case of water, and can be used in kitchen, basement, etc. Consider environmental protection factors. SPC floor is considered as a new generation of floor materials, which is characterized by extremely stable, high performance, complete waterproof, high-density sales core and pressure mark;It can be easily installed on different types of ground bases, concrete, ceramics or existing floors.Morelia, Whether to renovate the board.Fourth it is mainly the veneer thickness (decorative board thickness). The multi-layer solid wood floor has ,-, and the new three-layer solid wood floor has , to , mm.Generally, the moisture content of non dry wooden keel is about %, and that of qualified wooden floor is generally about %. If the humidity difference is too large, the wooden floor is easy to absorb moisture quickly. If the time is long, the floor will arch up and the paint will crack.Therefore, it is best to choose dry and straight wood as keel.After the keel level is determined, the keel and floor can be fixed with nails.