the driver of the construction electric elevator should inspect the construction electric elevator according to the requirements of the user manual and specifications

Setting requirements: Before starting work every day and changing shifts, record the inspection results and report any problems found to the user unit.High lifting height, using side mounted oil cylinders, stable operation, noise free, easy maintenance, and longer service life.peitaiho,When adding hydraulic oil,peitaihoGhent, we can extend the oil cylinder to the high position for filling. When filling, the lifting platform should not exceed the high position, and then retract the oil cylinder back to the low position to check if the hydraulic oil level is lower than the low position, and maintain it between the two.Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, and after changing the hydraulic oil, it must be automatically lifted and lowered to times to ensure that the air in the oil cylinder is completely discharged, maintain sufficient space, and ensure that the lifting platform can be lifted to the rated lifting height.Da Nang, and enters the lower end of the hydraulic cylinder through an oil filter,peitaihoBaile Atha I, explosion-proof electromagnetic directional valve, hydraulic control one-way valve, and balance valve,peitaihoShanxi, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge. The downward movement of the hydraulic cylinder (i.e. lowering of heavy objects).Setting requirements: The installation and dismantling workers, electricians, and other operators of construction electric elevators should have special construction operations.When the wall bracket cannot meet the requirements of the construction site, it should be designed and calculated separately.

The quality of the standard section should comply with the product manual and specification requirements.PoleSpeed limiter. To prevent the driving speed from exceeding the normal speed. A speedometer should be installed (not required for floors below or including the second floor), which is an individual mechanism that is integrated with a safety clamp; The entrance and exit of the passenger compartment should be equipped with safety doors. Public places, family dormitories, andTotal quality management,When the wall bracket adopts non matching standard products, design calculations should be carried out.Drivers of construction electric elevators should hold special construction operations and are not allowed to operate without a certificate.When the horizontal distance between the edge of the cage and the edge of the landing or between the cage and the landing door is greater than mm and there is no effective protection from other structures, the side protection device for the landing entrance should be equipped.

With the continuous improvement of urbanization level in China, the number of high-rise buildings in urban areas has sharply increased, and the height of buildings has also continued to grow. This has created a demand for high-altitude lifting platform vehicles. Therefore, in order to meet the needs of the domestic market and the public, efforts will inevitably be made to design and produce high-altitude lifting platform vehicles.Market trend,The net height of the landing door opening should not be less than m, and the difference between the net width and the outlet width of the cage door should not exceed mm. When the floor door is closed except for the gap between the lower part of the door that should not exceed mm, the size of any through-hole and opening related to the distance between any door and adjacent moving parts, as well as the gap around the door or between parts, should comply with the provisions of Table of 'Mechanical Safety - Safety Distance to Prevent Upper and Lower Limbs from Touching Dangerous Areas' GB-.Lower limit switch: In normal working state, before the suspension cage touches the buffer, otherwise protective measures shall be taken.peitaiho,The end height of the guide rail frame above the high attachment point should comply with the provisions of the user manual.Setting requirements: The guide rail should be rigid and flexible components such as wire ropes or chains should not be used.Many theaters use a lifting platform as a vertical transportation tool for goods. The rear of the main stage or the end of the side stage in many theaters are equipped with a set container transportation lifting platform, which is used to vertically transport items from the ground to a designated location or even the stage plane. The lifting platform of the music pool is often used for transporting movable seats, etc.