Boden townSelf priming slurry pump wholesaleDo you know how to use
2022-12-06 00:47:12The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining. Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mmBoden town, Stop the operation immediately under any of the following conditions: the current exceeds the rated value at the rated voltage; Under the rated head, the flow rate is much lower than that under normal conditions; Insulation resistance is lower than . megohm; When the dynamic water level drops to the pump suction; When the electrical equipment and circuit are out of specification The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!Gardabani, What is the solution to this situation? When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water
Rate. At present, all screw pump manufacturers regard dry operation protection as a necessary unit for equipment procurement. It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.ranking Start the priming pump. Moreover,Boden townAh slurry pump, the motor needs to be placed on the water surface for use during operation due to the structural limitations of the submersible slurry pump, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump Yes, industrial pumps have also increased in recent years.
When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view, it is to convert electrical or chemical energy into gravityFree consultation, First of all, lets understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, which leads to accumulation In fact, it is easy to distinguish whether a submersible sewage pump is a submersible pump or a sewage pump. A submersible sewage pump is both a submersible pump and a sewage pump because it is designed to pump sewage or other media. Its usage is to use it in water. Both names are acceptable. When Circumference. In the application of slurry pump, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product,Boden townSmall deep well pump,Boden townBooster pipeline pump, which can spray the precipitated slag into a mixture of water and solid particlesBoden town, ; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which is convenient and flexible. Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment. Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.