NibaiHigh strength plastic alloy pipeHow to choose
2023-02-15 09:27:14What is the purpose of flat steelI-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows:NibaiSeamless pipe has a high position in steel pipe, and there are many large factors. The main usage has accounted for more than %, which is applicable to all walks of life. Seamless pipe factories in China are widely produced. At present, the number of factories in China is also increasing every year, which is determined by the nature and production conditions of seamless pipe. The common production processes and processes are more complex.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Cao Lanh,Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementWhen selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Introduction to product knowledge of alloy pipe:
Plan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), the solution temperature is ~ ℃, and the solution time is min. According to the pipe wall thickness, pipes made of relatively thin materials such as steel strip can be welded with high frequency, and some thin-walled pipes can be welded with shielding gas; Pipes with wall thickness more than mm can be welded by hand. Small longitudinal crackInstallation conditions, there are many passivation methods for alloy tubes, profiled steel plate, etc.). Due to the reasonable section shape,NibaiHow much is 28b I-beam per ton, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, which is convenient for setting Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time and the waist is parallel to the roll axis.
Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);Honesty is the foundation,The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.Thin wall steel pipe, thick wall steel pipe.When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data,NibaiPrice of 42CrMo alloy pipe, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Lets take you to know:NibaiFunction of I-beam: where is I-beam mainly used?The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.The utility model has the advantages that the axial force of the roll is small, the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body, and more passes can be matched under the condition of a certain length of the roll body.