HokotenangoUsed pipeline pumpMacro positive boost the second price increase
2023-11-07 11:12:18When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed,HokotenangoSewage pump diving, otherwise the motor will fall into the water One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. WhenHokotenango, daily, weekly, maintenance and use plans shall be prepared for deep well pumps. there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore, in fact, it is mainlyDorado, The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned. Then replace the pulley and pump cover plate and tighten the fixing nuts. The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!
Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use. It is not allowed to operate the electric pump at high lift for a long time,HokotenangoPipeline pump body, and try to control it within the range of the proposed use lift, so as to prevent the electric pump from burning out the motor due to overload. Be sure to choose a pump that is more suitable for use.Sales Department, The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals. If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation otherwise the motor will not be burned due to too high medium temperature. It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.
Some impurities will entangle the impeller, so generally, the open impeller will be used, The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation. water quality: fine sand; Zhongsha; River and river water The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.Hokotenango, lets understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil which leads to accumulation When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water,HokotenangoSubmersible non clogging slurry pump, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.