if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　If the pump outputs more medium liquid, it will certainly do more work. If it sends less water, it will certainly do less work,　　AHR slurry pump is also a double pump casing structure, and the pump body and pump cover are equipped with replaceable corrosion-resistant rubber lining (including impeller, rear sheath,AkajutraSewage pump diving, etc.). The pump body and cover are the same as those of ah type slurry pump, and its transmission part and installation form are the same as those of ah and L type slurry pumps.　　Therefore when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.Ch’in-huang-tao,　　Carbon building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　 If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water, which will cause abnormal sound inside the pump, and then at the same time, the impeller is damaged or the impeller is damaged　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.

　　Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?　　However, it can also be called submersible sewage pump.　　 There may also be mechanical failure of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps waterStatistics,　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　A large amount of lubricating oil is stored.　　After meters,AkajutraSubmersible slurry pump, the sealing of the equipment can not bear the water pressure at this depth.

　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoidQuality Assurance,　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.　　Self priming pumps of different materials are used.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller the front guard plate and the rear guard plate is flat,AkajutraSingle stage slurry pump, stop, and tighten the two dust discs and fasten them on the shaft. adjustmentAkajutra,　　It is also necessary to clean the ventilation duct to avoid blockage.　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump