Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.When encountering signs of overheating in the electric motor, it is necessary to park the car in a timely manner, clean the problem and continue running. The motor bearings should be smooth and outstanding.Bayannur,BayannurManual pressure relief of hydraulic lifting platform,Hydraulic cargo elevator: Only when the load of the hydraulic guide rail type lifting cargo elevator cannot start working, should the pressure of the hydraulic system be checked. If the pressure is below the normal range the set value of the relief valve should be adjusted. Professional elevator manufacturers have high pressure resistance, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation resistance, and long service lifeWhen using hydraulic elevators, frequent inspections and maintenance should be carried out, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).Szigetszentmiklos,Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.

Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.Below, we will analyze for everyone. According to the market survey and understanding conducted by the editor of hydraulic freight elevator manufacturers, many customers choose hydraulic elevators instead of elevators due to the following reasons: narrow transportation location, which cannot meet the requirements of elevators; Unable to excavate the elevator shaft at the working location; Elevators are expensive and difficult to meet their needs.If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.Variable cost,The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, chain elevators, loading and unloading platforms, and attached electric construction platforms.After hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.The main device does not engage. When this fault occurs, check whether the three-phase power supply is normal, the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct, and whether the relay working indicator light is on.

The hydraulic lifting platform is a manually movable type, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.Customer first,Surface paint quality: The paint should be smooth and flat, have good adhesion with metal, have uniform color, no bubbles, no cracks, and there should be no wrinkles, pits, paint leakage, and sagging.When working on scaffolding without scaffolding or without railings, if the height exceeds meters, safety belts must be used or other reliable safety measures must be taken.Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it, improve the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.Bayannur,The hydraulic oil used in the system has the same brand, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.Lines of various safety equipmentTherefore, in the hydraulic pipeline assembly line, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.