I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height,St. Louis, Rio, ColoradoWelded pipe production and wholesale, the light I-beam has narrow flange thin web and light weight. Wide flange I-beam, also known as H-beam is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.According to the national standard of hot rolled H-section steel in China (GB / t- H-section steel is divided into narrow flange, wide flange and steel pile whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.St. Louis, Rio, Colorado,The fourth is the welding process method to ensure the strict implementation of the special operation method of galvanized pipe. The welding process includes pre welding groove inspection, control of welding process parameters and operation methods, post welding appearance quality inspection, and post welding nondestructive testing if necessary. Control the welding level and the amount of welding materials at each crossing. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.RUMA,Application characteristics of I-beamIt is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components, ladders, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.Alloy tube is widely used in our daily life, which provides us with great assistance. So what industries are alloy tubes applied to? Let&#;s follow the steps of all manufacturers and have a look together:

a. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe,St. Louis, Rio, ColoradoHow much is DN50 galvanized pipe, especially medium diameter small thick wall pipe, and can meet a large number of customer regulations on the specification and model of alloy pipe.According to the data information display information, there is an inseparable correlation between the annual real estate sales data information and the apparent consumption data information of galvanized pipe. From the consumption surface of the middle and lower reaches of galvanized pipe, decoration design, elevator car, handicrafts, household appliances and other industries are closely related to the situation of the real estate industry.→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.Create brilliance, The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.The system is mainly composed of control box, finishing roller, pre leveling unit, finishing unit and straightening unit.

I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.Trustworthy, Judged as failing.Installing the pipe structure means the complexity of some elements.Plan scheme : for high carbon steel with carbon content of more than .% and high chromium alloy pipe with chromium content of no less than %, the interval is min.St. Louis, Rio, Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment,St. Louis, Rio, ColoradoAlloy pipe, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.