close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.Ginotepe,　　Belt drive bearing assembly: the bearing assembly of this series of pumps adopts cylindrical structure which is convenient to adjust the clearance between the impeller and the front and rear guard plates, and can be removed as a whole during maintenance. The bearing is lubricated with grease.　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.Marrakech,　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same,GinotepeVertical slurry pump, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller

　　What?　　During the long-term overload operation of submersible sewage pumps, there are some common obstacles, such as the submersible pump cannot be started after it is powered on or the motor speed cannot be started after the submersible pump is started. A very small wait　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.Quality inspection report,　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　Carbon,GinotepeBaigang deep well pump,GinotepeScrew deep well pump, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment

　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pumpPotential development,　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　As a display screen, the operation of each fire pump is clear at a glance, and the management is very convenient.　　Only in this way can its service life be extended to a large extent.Ginotepe,　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.