MolfetaSmall hydraulic elevator,

For the introduction of daily maintenance of lifting cargo elevators, it must be washed off with gasoline or thinner.It is good not to cover the car with clothes for high-altitude work vehicles. If the vehicle is parked outside in windy and rainy weather, the clothes will repeatedly slap the car paint, especially if the car is blowing sand on the clothes, it will draw many small scratches on the clothes, because over time, it will lead to black paint. In addition, when the wind does not directly spray powder or clean the mechanism on the sand, it should be washed with water and prevent the high-altitude work vehicle vacuum cleaner from scratching the sand particles on the paint surface.Molfeta,Introduction to Fixed Boarding Bridge Loading and unloading Mobile Boarding Bridge is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.Usually, it is necessary to check whether each organization operates normally and whether there is any noise. If any obstacles are found, they must be quickly eliminated.Stropkov,Now that you understand how to use a hydraulic lift, it provides us with a safe working environment for our operators, and improves the efficiency and quality of the lowering work.The anti-corrosion measures for the body of high-altitude work vehicles should pay attention to small scratches. The paint surface of high-altitude work vehicles often corrodes. In addition to common collisions, scratches, and small rocks on the driving tires, there can also be a peeling point, which will cause a small rust over time. Because most of these scars are small and easily overlooked. Therefore, regular inspections should be conducted on the engine hood and surrounding areas. Once discovered, it is necessary to promptly go to a professional beauty shop for processing.Lifting and lowering

The key to using a hydraulic elevator during normal operation is to determine whether it is operating normally and whether there is noise based on its operating sound.The seat belt needs to be inspected every six months, with a load of kilograms. The test time is five minutes. After the test, check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.Now that you understand how to use a hydraulic lift, it provides us with a safe working environment for our operators, and improves the efficiency and quality of the lowering work.property right,Usually,MolfetaMobile lifting hydraulic platform, it is necessary to check whether each organization operates normally and whether there is any noise. If any obstacles are found, they must be quickly eliminated.Each box, distribution box, etc. is usually kept clean,MolfetaExplosion proof hydraulic lifting platform truck, and dust on electrical equipment should be quickly swept away.Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %

This fixed lifting device can also be used in the warehouse, such as lifting a certain layer of the warehouse to transport goods or personnel to a designated storage location.Direct laborAttention should be paid to inspecting whether each steel wire rope has broken wires and loose strands. If it exceeds the relevant regulations, it must be replaced immediately. The care and maintenance of steel wire ropes should strictly follow the regulations.Do not adjust the solenoid valve on the motor arbitrarily. The solenoid valve is pre adjusted before leaving the factory and random adjustment can easily cause internal pressure to increase or decrease. In severe cases, it can shorten the service life of the motor.When installing, and adjusting the exhibition organization, attention should be paid to ensuring that the center line of the exhibition organization reducer is parallel to the center line of the gear, and its meshing surface is not less than %, and the meshing interval should be appropriate.Molfeta,Usually, it is necessary to check whether each organization operates normally and whether there is any noise. If any obstacles are found, they must be quickly eliminated.What is the new price for fixed elevators?The rust prevention work of aerial work vehicles is generally something that needs to be paid attention to when they have not been used for a long time. How should we do anti-corrosion on the body of aerial work vehicles? This is actually a simple matter of not having to spend money on anti-corrosion at the repair station. As long as we car owners use some materials they can find on their own, we can achieve this. At the same time, paying attention to driving habits can ensure that high-altitude work vehicles do not rust. Here are a few points for reference.