The polyurethane insulation board shall be connected by plug-in notch connection, because it has higher strength when connecting in this way.The foaming technology of polyurethane with strong stability makes it have superior bonding performance. The firm combination of polyurethane rigid foam and carrier layer is the basic premise to ensure the stability of external insulation layer. That is,Ciudad Juárez Which is a good cold storage project installation, under the unfavorable local temperature and humidity conditions, it can bear various internal and external combined loads such as wind force, self weight and normal collision, and the insulation layer still does not separate and fall off from the carrier layer and remains stable in the state.Ciudad Juárez ,Water defrosting: spray the defrosting water spray device on the surface of the evaporator to melt the double layer, and then through the drainage pipe. This scheme has high efficiency, simple operation procedure and small temperature fluctuation. From the perspective of energy, the cooling consumption per square meter of evaporation area can reach -kj. Water frost flushing is also easy to make fog in the warehouse, cause dripping water on the ceiling of the cold room, and reduce the service life.For the flushing (thawing) drainage pipe in the cold room with different temperature, an exhaust valve equipment shall be set before connecting the flushing (thawing) drainage pipe.Agere Maryam,The service life of polyurethane cold storage insulation material foam is: besides the basic performance of the initial stage of polyurethane foam, the deterioration of foam performance is also a very important index. When the white material is prepared, the surface of some polyester materials can make the foam have better toughness and impact resistance, and will no longer resist impact and collision. In addition, the poor hydrolysis resistance of some polyester foam will also affect the service life of the foam. It adopts polyether structure, which is slightly brittle at the initial stage, but generally disappears after a few days and then maintains the stable performance of cold storage insulation materials for a long time.The common phenomenon of quick freezing storehouse is that the temperature of quick freezing storehouse can't drop down or drops slowly. Now, resulting in poor thermal insulation and thermal insulation effect a simple analysis is made on the reasons for the slow drop of temperature: the cold capacity loss of quick freezing storehouse is large due to poor thermal insulation or sealing performance; the poor thermal insulation performance is due to insufficient thickness of thermal insulation layer of pipeline and warehouse thermal insulation wall, It is mainly caused by improper selection of insulation layer thickness in design or poor quality of insulation materials in construction.The overall construction achievements of the cold storage project have been put into use, and the service life can reach years.

For the flushing (thawing) drainage pipe in the cold room with different temperature, an exhaust valve equipment shall be set before connecting the flushing (thawing) drainage pipe.The whole equipment is clean and the environment is clean.For the flushing (thawing) drainage pipe in the cold room with different temperature, an exhaust valve equipment shall be set before connecting the flushing (thawing) drainage pipe.quality,Points of multi-storey cold storage: small, which can save land; When the storage capacity is the same, the surface area of the outer enclosure structure is smaller than that of the single-layer cold storage, so that the cold consumption can be reduced, the dry consumption of food can be reduced, and the machinery and equipment cost and operation and management cost can be reduced accordingly. At the same time, due to the saving of thermal insulation materials, such as the cooling room can be used as the cold storage room, the attic on the top floor can be built into the ice making room, etc.More and more people begin to build cold storage, and most people choose to use cold storage for cold storage construction. Why? Why do people choose cold storage for construction? What are the advantages of cold storage? The following is a detailed introduction.In order to prevent damage to the cold storage, it is necessary to lay some foam on the floor of the cold storage tank.

Whether there is dirt on the condenser and poor heat dissipation will lead to too high condensation pressure of the refrigerator. In order to protect the compressor, the machine stops running under the action of the pressure controller. When the heat dissipation is good, press the black reset button on the pressure controller, and the machine can automatically resume operation.Administration,The overall construction achievements of the cold storage project have been put into use and the service life can reach years.Do a good job of power failure early warning. The management personnel of the controlled atmosphere storage shall often pay attention to the notice of the local power department. In case of power restriction or line transformation, they shall do a good job in time. For sudden power equipment failure and artificial line, it is recommended to install power failure alarm, and the loss will be reduced to a low level.Polyurethane foam: This is also a very common cold storage material. It has strong thermal insulation effect and strong mechanical strength. Now it is widely used and has a good application prospect.Ciudad Juárez ,Artificial refrigeration keeps the room at a constant temperature. The walls, floors and flat roofs of large cold storages are laid with thermal insulation materials with a certain thickness to reduce the incoming heat from the outside. In order to reduce the absorption of solar radiation, the construction form of food cold storage warehouse is to determine the plane layout based on the site, whether it is a single-layer or double-layer warehouse, and the structure is the selection of steel structure or reinforcement solidification. Cold storage capacity, production process, refrigeration, product stacking, temperature, etc. are used to determine the size and location of the cold storage room,Ciudad Juárez Installation of small cold storage equipment, so that it can become a whole.In the process of realizing your dream, you must remove all the influences. It is very important to recognize that when these beautiful refrigerators are built in the villa room, the collection pit (pool) for flushing (thawing) and drainage should adopt the Countermeasures of avoiding freezing and cleaning and avoiding backflow of water.