Pull square tube:With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.Las cambres,At the same time, the heating temperature and heating time will also have a great impact on the performance of square tube. The heating of square tube blank is the key process to ensure that the square tube blank has enough plasticity and complete the smooth perforation. If the heating temperature is too high or the heating time is too long, the billet of the square tube will be burned and decarburized, and even the chemical composition of the square tube will be unqualified (unqualified carbon content), which is easy to cause batch quality problems and seriously affect the product qualification rate.Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionKiziltepe,The difference between square pipe and seamless steel pipe the main feature of seamless steel pipe is no welding joint and can withstand large pressure. The product can be very rough as cast or cold drawn parts.C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.

The disadvantage of empty bending is that when the upper side and side are synchronously empty bending, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave, and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot,Las cambresGalvanized square pipe, billet or square tube Make materials of all shapes, which requires us to conduct comprehensive consideration and analysis. In particular, the quality and level of the paint and the relevant technical level deserve our attention. Note that the square tube should not be used immediately after painting, but should be placed for a period of time and wait until the paint is dry!Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.quality index,B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.

Qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same, but their uses are very different. The shape is different. Qb square tube is a cuboid and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.Direct labor,Qb square tube, qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.The raw material for rolling square tube is round tube blank. For a long time, square tube, rectangular tube, seamless square tube, galvanized square tube and galvanized tube have complete products,Las cambresFabrication of galvanized square pipe, excellent quality and favorable price. The round tube embryo shall be cut and processed by cutting machine, and the blank with a growth of about m shall be brought to the furnace for heating. The billet is sent to the furnace for heating at a temperature of about degrees Celsius. The fuel is hydrogen or acetylene. The temperature in the furnace is the key problem. After the round tube billet is discharged from the furnace, it should be pierced through the pressure piercer. Generally, the more common piercer is the conical roll piercer. This piercer has high production efficiency, good product quality, large perforation expansion and can wear a variety of steel grades.Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, etc; Low alloy steels are divided into q Mn, Q,Las cambresHot dip galvanized seamless steel pipe for inner and outer wall, St-, etc.Las cambres, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.