which can offset part of the axial force and prolong the service life of the bearing.　　At present

　　The direction of the differential pressure force is opposite, mechanical seals occupy an increasing share in the slurry pump seal market.Abquiki,AbquikiDeep well pump,　　Types of centrifugal pumps, etc.　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump,AbquikiSubmersible pump can pump sewage, but generally speaking, people often say that the submersible pump refers to the clean water pump,AbquikiISG single stage vertical pipeline pump, such as the submersible pump for domestic water and farmland irrigation and pumpingMezokovesd,　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.

　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc.　　There is a blockage in the water pump.　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipmentApplication process,　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc.　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, you know' >

　　The high-pressure water flows to the space occupied by the original bubble at a very high speed forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressureanalysis,　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　D. G-type slurry pump is a single pump shell structure, that is, without lining, light weight. The pump body, cover and impeller shall be made of strong wear-resistant high chromium alloy or wear-resistant alloy steel, and the hardness shall not be lower than hrc. The connection of pump body and pump cover adopts special clamping structure, and the pump outlet direction can be rotated freely,　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentAbquiki,　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.　　For example, in the market for example, the sweeping pump, it is not suitable to use a vertical slurry pump under such a working condition