the pump needs to be placed on land

　　When the submersible slurry pump works, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump,WolfsburgVertical slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing,WolfsburgBaigang deep well pump, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasionWolfsburg,　　(b) The maximum ambient air temperature varies with seasons, but does not exceed ℃.　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first,　　Causes: there is air or gas accumulation in the water inlet pipe of the pump or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.　　Therefore, the stator winding will be burnt out due to excessive temperature rise.

　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve　　Although they are both pipeline pumps among centrifugal pumps, there are still many categories. Next, let&#;s talk about some models of pipeline pumps and their respective uses.　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageQuality inspection report,　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint,

　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall bemiddleman,　　Circumference. In the application of slurry pump, we must pay attention to reasonable design correct calculation and appropriate type selection, which are very important. In addition to the main wheel,WolfsburgDeep well submersible pump, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　 there are two different installation methods, fixed automatic coupling installation system and mobile free installation system.　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulationWolfsburg,　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.