It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, which makes the flow increase after the impeller is cut.Ginotega　　 The power line of the submersible sewage pump is relatively long, and it is difficult to start the submersible pump. A larger cable is required. If the distance is long so the voltage drop is too large, the submersible pump should be close to the transformer.　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.Tikrit,　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor

　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　Solution: replace the remote pressure gauge; Replace the pressure transmitter; Check the connecting signal wire.　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration,GinotegaSubmersible slurry pump, and the site is cleaner.Quality recommendation,　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.　　In fact,GinotegaVertical slurry pump, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　Pump, sewage submersible pump and seawater submersible pump.

　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.Quality recommendation, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　 the float switch can automatically control the start and stop of the pump according to the required liquid level change, without the need for special personnel, which is very convenient to use.　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.Ginotega,GinotegaSelf priming slurry pump wholesale,　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)　　The packing seal auxiliary impeller seal and mechanical seal are mainly used. Among them, the packing seal needs small leakage and is not suitable for transporting toxic, corrosive and precious liquids; The sealing of the auxiliary impeller relies on the reverse pressure of the two sealing impellers during rotation to prevent the leakage of the medium, and can also play a role in