Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submergedCandlestick,　　The main shaft of the water pump is bent or the main shaft of the water pump and the motor is not concentric or parallel.　　Flexibility. The equipment has advanced structure, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles strong sewage discharge capacity, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.Massaguet,　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable,CandlestickSplit vertical pipeline pump, but the price is quite expensive.　　Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.

　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone,CandlestickSubmersible pump can pump sewage, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　The discharge side of the pump must be equipped with a valve (ball valve or stop valve, close the cock connected with the submersible slurry pump before starting the motor, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.Welcome calls ,　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.

　　During adjustment, firstly loosen the support cover then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationFinance Department,　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees,CandlestickVertical slurry pump, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.　　The ability of dirt passing through makes it safer to use.　　 First remove the pump from the engine.Candlestick,　　In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.