How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.　　 if the removed gasket is seriously damaged a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Chenandega, it is necessary to prevent damage to flow passage components caused by water hammer.Helsinki　　 the experimental water shall meet the relevant process requirements.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown,　　Submersible slurry pumps are mainly used in mining, metallurgy, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service life　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.

　　With water, you can start working.　　 Disassembly of water pump: use a disassembly wrench to remove the water inlet joint by left rotation,ChenandegaVertical slurry pump, and use a disassembly cylinder to impact the conical sleeve at the lower part of the pump. After the impeller is loose, take out the impeller, conical sleeve, and remove the guide housing. In this way, the impeller, upper guide housing, check valve, etc. are unloaded in turn.　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pumpApplication process,　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　 We must choose to consider the actual use situation when making the selection,ChenandegaSelf priming non clogging sewage pump,ChenandegaTwo stage slurry pump, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.Application process,　　 First remove the pump from the engine.　　How to prolong the service life of the submersible sewage pump Replace the sealing ring: after long-term use in the sewage medium, the gap between the impeller and the sealing ring may increase, so it should be replaced in time.　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.Chenandega,　　There are differences.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)