X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Guazar,Are there many welded types of mesh produced? According to the welding type and overall improvement, the difference between the reinforcement mesh and the welded mesh is not particularly large. It is still due to the scattered quality of the southern city. From the perspective of development to the longitudinal and transverse interleaving devices of the reinforcement mesh, the bound or welded mesh has better application quality.After isothermal quenching treatment, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment.Pisandou,The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.Reinforcement mesh is manufactured by automatic and intelligent production line under the strict quality control of the factory. Grid size,GuazarWhere do you sell welded pipes, reinforcement specification and quality are strictly controlled. The longitudinal and transverse bars of the reinforcement mesh form a network structure, so it has good bonding and anchorage with the concrete, and the load is evenly distributed, which obviously shows the seismic crack resistance of the reinforced concrete structure.Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace, chemical industry, electric power,The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.What is nitriding of alloy pipeWhat should we pay attention to in the production of alloy pipe

→ the two surfaces of the flange are parallel to each other,GuazarHow much is 65 welded pipe per meter, making it easy to connect, process and install.Excellent service,GuazarHow many kilograms per meter of 100 welded pipe,The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment and the reproducibility of the solution is good.General welded pipe: General welded pipe is used to transport low-pressure fluid. It is made of qa, qa and QA steel. It can also be made of other mild steel that is easy to weld. Water pressure, zigzag, flattening and other tests shall be carried out for steel pipes, and there are certain requirements for surface quality. Generally, the delivery length is -m, and fixed length (or double length) delivery is often required. The standard of welded pipe is expressed in nominal diameter (mm or inch). The nominal diameter is different from the actual. Welded pipe can be divided into general steel pipe and thickened steel pipe according to the specified wall thickness, and steel pipe can be divided into threaded and non threaded according to the way of pipe end.Alloy pipes can be used for heating (cooling) projects.GuazarWhen we carry out different projects, we must use different raw materials, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns.The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.