AnaheimVortex pump and pipeline pump,

　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterAnaheim,　　 optimal water inflow of well m/h　　Water flow into the bearing damages the bearing.Kimbe,　　Fourth, model selection parameters: outlet diameter, flow, dust, motor power, impeller speed, pumping rate, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.

　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　Pipeline pump is also called pipeline centrifugal pump. According to the structure, pipeline pump can be divided into vertical pipeline pump and horizontal pipeline pump. Can the pipeline pump suck water? Recently, a customer asked this question. Most pipeline pumps have self-priming . It&#;s just that different types of pipeline pumps　　 If it is found that the impeller is damaged and the liquid supply is insufficient it is necessary to replace the new impeller in time for use.Recommendation and consultation,　　In this way, a smooth surface can be formed on the surface.　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate and press out the middle impeller and water seal.　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.

　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller),AnaheimSmall deep well pump, magnetic dial indicator, outside micrometer, caliper, square ruler, copper bar, screwdriver with handle,AnaheimVertical centrifugal slurry pump, hammer, V-shaped irons of the same specification, oil basin, cotton yarn, etc.How much does it cost?,　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, the pump should also have good corrosion resistance high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics　　. Check and solve the problems such as power line disconnection, cable connection, motor winding not burnt, etc.　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller which can pump out the slag settled at the bottom after stirring into turbulence. impellerAnaheim,　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.