Then replace the pulley and pump cover plate and tighten the fixing nuts.　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum,Barclay Nettlefold ,　　Types of centrifugal pumps etc.　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impellerHon Gai, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.

　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate,Barclay Nettlefold Non clogged pipeline sewage pump, and press out the middle impeller and water seal.　　 Each drainage and irrigation period ( hours) shall be provided with a maintenance protection, and the replaced vulnerable parts shall be replaced.　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year there is still a large gap after China&#;s power balance.Quality improvement,　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　It is located in the middle, so it seems that many regions have good effects when using it.

　　Reasonable.Recommendation and consultation,　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　Its working principle is as follows: when the screw pump is working, the liquid is sucked into the sealing cavity formed by the rotor and stator. Due to the rotation of the rotor, the liquid follows the sealing cavity to move along the axial direction from the suction side to the discharge side of the pump, and the continuous suction and discharge realize the liquid transmission .　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.Barclay Nettlefold ,Barclay Nettlefold Split vertical pipeline pump,　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation,Barclay Nettlefold Wear resistant slurry pump, otherwise the motor will not be burned due to too high medium temperature.　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.