After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.Oklahoma,Seamless pipe production processIn order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.Resen,→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.I-beam, whether ordinary or light, so its application range is very limited. I-beams are widely used in buildings and other metal structures.The utility model has the advantages that the axial force of the roll is small the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body, and more passes can be matched under the condition of a certain length of the roll body.

What is nitriding of alloy pipe According to the pipe wall thickness, pipes made of relatively thin materials such as steel strip can be welded with high frequency, and some thin-walled pipes can be welded with shielding gas; Pipes with wall thickness more than mm can be welded by hand.It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact, this cognition is wrong. H-beam and I-beam are different in shape!Honest service,The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Requirements of alloy tubes for low and medium pressure boilers

The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Discount,Oklahoma12CR2MOG alloy pipe, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe, which has incomparable advantages of other processing technologies, and can meet a large number of customer regulations on the specification and model of alloy pipe.Pipelines of various specifications and models are complete.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.OklahomaThe utility model has the advantages that the axial force of the roll is small, the axial movement is small, and the working slope is not required,The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small) a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline,Oklahoma38CrMoAl alloy pipe,OklahomaHow much is 219 welded pipe per ton, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.