In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.The system is mainly composed of control box,PetrikovHow much is the wholesale price of welded pipe, finishing roller, pre leveling unit, finishing unit and straightening unit.Petrikov,This phenomenon is affected by cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Application scope of alloy pipeThe shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.

When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.In our daily life and work, we can often see a lot of steel products. At the same time, among many steel products, the figure of galvanized pipe is particularly prominent. This is because this kind of pipe will be applied to many engineering construction we often see in our life. There are also countless products processed with this kind of pipe. For example, in the field of mechanical equipment processing we often see, the application of galvanized pipe is more frequent. Let&#;s discuss the application scope of this kind of pipe today.c. quality inspection is carried out for alloy pipes, so that the whole process of steel pipe processing is under reasonable inspection and supervision, and the product quality is reasonably guaranteed.Where to sell API,PetrikovWelded pipe production and wholesale,Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilityAlloy pipe is a spiral seam seamless steel pipe,PetrikovHow much is a ton of high frequency welded pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.

It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact, this cognition is wrong. H-beam and I-beam are different in shape!Inspection standard,Its heat sealing effect is remarkable. It can be directly buried immediately which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, and reduce the construction cycle time of the project. On the whole it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Galvanized pipe, is divided into hot-dip galvanizing and electro galvanizing. The hot-dip galvanizing layer is thick, the coating is uniform, the adhesion is strong and the service life is long. The electroplating cost is low, the surface is not smooth, and the corrosion resistance is worse than that of hot dip galvanized pipe.→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.Petrikov,Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, low cost, easy maintenance, durable economic development and convenient product specification transformation. For example, the production of large diameter must be grooved pipe, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, thick wall and thin alloy steel pipes, and can not exceed the working capacity of thick wall pipes of machinery and equipment.