Tecpan, GuatemalaLong shaft submerged slurry pumpWhat is the proportion of
2023-10-09 14:20:30Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump Therefore, the stator winding will be burnt out due to excessive temperature rise.Tecpan, Guatemala, Clean up the silt and other obstructions in or around the water pump. During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests,Tecpan, GuatemalaSubmersible sewage pump, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact,Tecpan, GuatemalaIrrigation deep well pump, we use it at ordinary timesPryluky, Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s. The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates. for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places. The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times so it has an irreplaceable position when it is used. What is its own structure when it is used.
Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to For /g-g gravel pump, which belongs to large-diameter slurry pump, it is necessary to remove the impeller removal ring and rotate the impeller in the opposite direction. Rate.Quality improvement, If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump. This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, the pump should also have good corrosion resistance high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Lets have a look.
It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipmentCustomer first, Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability. The treatment methods are as follows: Check the power supply voltage: if the voltage changes greatly, it is caused by unstable voltage, and the use should be stopped immediately to prevent more serious consequences. Or install corresponding heat dissipation protection measures to protect the motor. Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, Guatemala, Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, seawater lifting ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation