As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market,Because of this characteristic, seamless pipe is widely used in oil transportation natural gas,IrapatoInconel 600 seamless pipe, natural gas, water and some solid materials transportation. Smooth steel pipe has strong bending advantages compared with other steel pipes. And the smooth steel pipe is also light in weight. It is a very economical single-sided steel.Xhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum, niobium, francium and other components. The alloy carbide formed has strong stability at high temperature.Hatvan,The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore,IrapatoWhat software is there for steel bar turning, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.

H-section steelThe whole structure is composed of zinc and quaternary crystals, forming dense crystals and barrier layer on the plate, which effectively prevents the penetration of corrosion factors. From the point of view of the strong zinc corrosion resistance of the barrier layer, when the zinc sacrificial anode is at the forefront of protection, the scratches and scratches of some coatings and the insolubility of zinc oxide layer play a protective and blocking role. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.Test method,Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs. Remove defective pipes within the allowable length.Stages needing attention in the production and manufacture of alloy tubes

Stages needing attention in the production and manufacture of alloy tubestotal cost,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.The multi-al combination of reinforcement mesh welding machine and reinforcement mesh row welding machine based on PLC basic control. At present,IrapatoWhat is the price of 25 steel bars, the full-automatic mesh welding machine has the characteristics of simple operation high control precision and easy to master the process of high-speed continuous welding.GB No. I-beam is in height, in leg width and in waist thickness.Irapato,Classification introductiond. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information, and the performance parameters in the production process are monitored by the central control room.I-beam