There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.Matansas,　　What faults will the water pump control cabinet often encounter in use? The water pump cannot work: cause: a. the power supply is not connected or the output phase of the control cabinet is missing; b. The water pump has been burnt out,MatansasSelf priming non clogging sewage pump, and the water pump can not supply water: cause: A. whether there is water in the pool; b. Whether there is gas in the pump body that is not discharged; c. Inlet and outlet water　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.Villamontes,　　Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft and successively install the bearing inner race, bearing gland and retaining sleeve　　Fourth, model selection parameters: outlet diameter, flow, dust, motor power, impeller speed, pumping rate, maximum particle and weight.

　　In addition, drain it, change the oil, and then tighten the screw plug.　　Stop, then tighten the bearing seat, press down the nut and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is looseInspection items,　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.

　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pumpRecommendation and consultation,　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　Solution: replace the remote pressure gauge; Replace the pressure transmitter; Check the connecting signal wire.　　 There is also a vibration method to measure the vibration frequency of the pump,MatansasAh slurry pump, and the measurement is relatively simple. However, when using one method,MatansasSubmersible slurry pump, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the mainMatansas,　　The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.　　After meters, the sealing of the equipment can not bear the water pressure at this depth.　　Whether it is the pre installation inspection or the post installation commissioning inspection