SacramentoLarge cold storage installation companySelect the properties of the bullet point

2022-03-11 00:44:33

In the low temperature environment, especially in the periodic freezing and thawing cycle, the building structure is also vulnerable to. Therefore, its installation quality will directly affect the temperature of cold storage. As an important structure used in the cold storage, the cold storage board should pay attention to the details of its installation, find out the problems that are easy to be ignored, and avoid the wrong installation which will affect the use of the cold storage or the whole installation process, so as to waste resources and increase the cost.Sacramento,Due to the slow cooling, all equipment will consume electric energy during operation. If the cooling is slow, the equipment will stop and cannot consume electricity, so the electricity charge will not be consumed. As a high energy consuming equipment, the daily power consumption of cold storage is relatively large. If the refrigeration effect is not good, the annual use cost will directly double several times. Moreover, if the equipment operates for a long time, the service life will be reduced accordingly, which is something users don't want to see.Acid disinfectant can be used for mold removal and disinfection of quick-frozen warehouse.Wesselsbron,The ultrasonic town is a patented technology with a shaped energy cover, which increases the effective humidification amount by -% per hour. What are the reasonable aspects of the design of the quick freezing warehouse?Indirect cooling is that the air in the warehouse is pumped into the air cooling device by the blower. The air is absorbed by the evaporation pipe circling in the cooling device, and then sent to the warehouse for cooling. The advantages of air cooling are rapid cooling,SacramentoInstallation of fruit and vegetable fresh-keeping warehouse, uniform temperature in the warehouse, and can bring harmful gases such as carbon oxide out of the warehouse during storage.In order to prevent damage to the cold storage, it is necessary to lay some foam on the floor of the cold storage tank.

SacramentoLarge cold storage installation companySelect the properties of the bullet point

Cold storage design segmentation: several different partitions shall be reasonably planned and divided according to purpose and temperature. For example: processing room, sorting room, quick freezing room, refrigeration room, channel, unloading platform, etc.The area of wires in the conduit shall not exceed %.If there is more air or refrigerant oil in the evaporator, the heat transfer effect will be reduced: once more refrigerant oil is attached to the inner surface of the evaporator heat transfer tube, the heat transfer coefficient will be reduced. Similarly, if there is more air in the heat transfer tube, the heat exchange area of the evaporator will be reduced, the heat transfer efficiency will be significantly reduced, and the decline rate of warehouse temperature will be slowed down.Welcome to inquire,Cork board: cork board can be said to be a relatively primitive kind of cold storage. The thermal conductivity of cork board is relatively low, and it is easy to obtain, so it is not difficult to process, so it is generally used as the insulation board in some ordinary cold storage. If you want to pursue better thermal insulation performance, you have to look at the following materials.The closed cell structure and surface material of polyurethane rigid foam with good moisture-proof, waterproof and corrosion resistance make it have better air resistance and water vapor resistance, which is easy to assemble. It does not need additional insulating layer to prevent moisture and saves a lot of trouble in laying insulating layer.The quick freezing storehouse of vegetables and fruits is not suitable to use exhaust cooling, because the gas in the quick freezing storehouse needs to be circulated and dispersed regularly to avoid carbon oxide poisoning caused by high concentration of carbon oxide in local areas. Therefore, in the quick freezing warehouse, the refrigeration equipment needs to be used together with the air conditioning equipment. The selection of refrigeration equipment is different from that of low-temperature freezer and ordinary quick freezing warehouse.

SacramentoLarge cold storage installation companySelect the properties of the bullet point

Moreover, polyurethane does not produce harmful gas at high much, and the refrigerating capacity can not meet the load requirements of the warehouse: due to the long-term operation of the compressor, the cylinder sleeve, ring and other parts are seriously worn, the long-term cold storage installation, installation, construction, fruit preservation, medical cold storage and other brand products, the designated products are complete, the quality is guaranteed and the sealing performance will be reduced accordingly with the increase of the matching clearance, The gas transmission coefficient of the compressor will also be reduced, and the refrigeration capacity will be reduced. When the refrigerating capacity is less than the heat load of the warehouse the temperature of the warehouse will drop slowly.Does the unit location meet the relevant conditions? Whether the heat dissipation and pipe length can meet the requirements. - floor installation of cold storage: first level the floor, then install the floor, select a beautiful floor and put it in a conspicuous place, and do a good job in the floor and evaporator drainage system.SacramentoThe new cold storage material is made of rigid polyurethane or polystyrene foam insulation sandwich panel, which is made by high pressure foaming process and can be made into various lengths and specifications to meet the different requirements of the users.Fault phenomenon: high current or tripping during unit startup,SacramentoFruit refrigeration, and problems of user air switch; Input voltage is too low; The star angle conversion interval is too short (it should be ~ seconds); Hydraulic cylinder failure (no reset); Intake valve failure (too large opening or stuck); Loose wiring; Host failure; Main motor fault; TR time relay is broken (relay unit).The refrigeration of cold storage pays more and more attention to the needs of environmental protection and energy saving. Professional projects include: cold storage installation, installation of cold storage, cold storage construction, fruit fresh-keeping cold storage, medical cold storage and other related businesses. Merchants who hope to have this business please consider the wide scale of warehouse temperature control,SacramentoFreezer installation, the selection and placement of cooling equipment and the description of wind speed field, which are suitable for the cold storage needs of a variety of goods. Equipped with perfect storage temperature active detection, recording and active control equipment.

404 Not Found

404 Not Found


Related articles

SacramentoLarge cold storage installation companyIndustry quality standards

SacramentoLarge cold storage installation companyIndustry quality standards

The combined cold storage door starts frequently or does not start for a long time, or stops before...


2022-03-11 09:38:41

Yes, SacramentoLarge cold storage installation company good quality and great value for money

2022-03-11 08:55:59

SacramentoLarge cold storage installation company It’s good, the price is right, friends also say it’s good, it’s worth it

2022-03-11 08:47:35

Ha ha. SacramentoLarge cold storage installation company It’s here so soon, it’s not bad, next time you come, you can ask for a discount ^_^

2022-03-11 09:37:30

Just paid, when will SacramentoLarge cold storage installation company arrive, boss.

2022-03-11 09:26:33

Can you give me a discount next time I buy it, SacramentoLarge cold storage installation company The quality is good, and I will live up to the boss