Using CrO and hsoho as the main components and adding an appropriate amount of mnso.ho coloring solution, coloring solution temperature, mass concentration and coloring time on the color film of stainless steel industrial pipe were discussed. Through a large number of experiments, a good formula and process range of coloring solution are obtained. With the increase of temperature and time, the film thickness increases, and the color changes are brown, blue, gold, purplish red and green. After curing and sealing treatment, the colored film of stainless steel industrial pipe has more uniform surface color, good reproducibility, and significantly improved wear resistance and corrosion resistance.Austenitic stainless steel is generally used for manufacturing and manufacturing chemical equipment components, low-temperature equipment components in refrigeration industry, and can be used as stainless steel spring and clock spring after deformation strengthening.Nuevitas, s is the abbreviation of steel,Nuevitas3mm thick stainless steel pipe, P is the abbreviation of plate, h is the abbreviation of hot heat, and C is the abbreviation of commercial. It generally represents hot-rolled steel plate and strip.Chloride ions exist in the service environment. Chloride ions exist widely, such as salt, sweat, sea water, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions, even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough, the container leaks due to corrosion days after it is replaced with stainless steel.Anjala,Application fields: chemical industry, construction industry.According to the purpose, it can be divided into oil well pipe (casing, oil pipe and drill pipe), pipeline pipe, boiler pipe, mechanical structure pipe hydraulic prop pipe, gas cylinder pipe, geological pipe, chemical pipe (high-pressure chemical fertilizer pipe, petroleum cracking pipe) and marine pipe.CE--“ Code for design of cold formed stainless steel structural parts & rdquo; And & ldquo; jointly published by nidi and euro inox; Structural stainless steel design manual & rdquo; The design of structural parts for buildings with long service life and good integrity has been simplified.

Marking: in order to make the steel pipe complete the socket of the pipe fitting,Nuevitas430 stainless steel strip, the length must be marked and marked at the pipe end.The internal and external greasy dirt and sundries at the pipe end shall be completely removed to keep the pipe inside the pipe fittings clean.Stainless steel pipes and water transmission equipment for fluid transportation such as water and gas are advanced basic water purification materials in the world. They have strong anti-corrosion performance, which can not be compared with cast iron pipes, carbon steel pipes and plastic pipes.Home page recommendation,As long as the steel type is selected correctly and maintained properly, stainless steel will not produce corrosion, pitting, corrosion or wear. Stainless steel is also one of the high-strength materials in metal materials for construction. Because stainless steel has good corrosion resistance, it can ensure that the structural components can maintain the integrity of engineering design. Chromium containing stainless steel also integrates mechanical strength and high extensibility and is easy to wear The processing and manufacturing of parts can be fullThe petrochemical industry, including the chemical fertilizer industry, has a great demand for stainless steel pipes. Stainless steel pipes are mainly used in this industry, including, , l, etc. with an outer diameter of about ￠ - ￠ and a wall thickness of about mm-mm (generally medium and low pressure transmission pipes with a specification of more than & phi; mm). The specific application fields are: furnace pipes, material transmission pipes, heat exchanger pipes, etc. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the steel plant is that the peeling and trachoma of the steel strip will cause rust. Substandard materials will cause rust. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the pipe manufacturer: the welds in the pipe manufacturer are polished rough, which will cause rust.

Stop the written technical disclosure, on-site technical and safety disclosure to the on-site operators.Discount,There are three main reasons for oxidation of stainless steel: production process, which is one of the reasons for oxidation of steel products. In terms of production process and product characteristics, forming a thin oxide film on the product surface is the basic process to avoid oxidation, and it is also one of the main characteristics of steel products different from other steel products. It is specialized in products, renewable resources business and business package Including: stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe. However, when the oxide film is incomplete and discontinuous due to insufficient or negligent production process, the oxygen in the air will directly react with some elements in the product, resulting in the appearance of oxidation of the product.Seamless steel pipe): round billet & rarr; Heating → Perforation & rarr; Three roll cross rolling, continuous rolling or → Off pipe & rarr; Sizing (or reducing) → Cooling → Straightening & rarr; Hydrostatic test (or flaw detection) → Mark & rarr; The raw material for warehousing and rolling seamless pipe is round pipe blank. The round pipe blank shall be cut and processed by cutting machine, and the blank with a growth of about m shall be brought to the furnace for heating. The billet is sent to the furnace for heating at a temperature of about degrees Celsius. The fuel is hydrogen or acetylene. The temperature in the furnace is the key problem. After the round tube billet is discharged from the furnace it should be pierced through the pressure piercer. Generally, stainless steel belt and stainless steel pipe, with high pressure resistance grade, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection, long service life, large perforation diameter expansion, and can wear a variety of steel grades. After perforation, the round tube blank is successively rolled by three roll cross rolling, continuous rolling or rolling. Take off the pipe after sizing. The conical drill bit of the sizing machine rotates into the steel embryo at high speed to form a steel pipe. The inner diameter of the steel pipe is determined by the outer diameter length of the sizing machine bit. After sizing, the steel pipe enters the cooling tower for water spray cooling. After cooling, the steel pipe is sent to the metal flaw detector (or hydrostatic test) for internal flaw detection. If there are cracks, bubbles and other problems inside the steel pipe, they will be detected. Steel pipes should be strictly selected manually after quality inspection. After the steel pipe is inspected, the number, specification, etc. shall be sprayed with paint. And hoisted into the warehouse by crane.The bearing capacity of decorative stainless steel pipe ice load is the main control load of offshore platform in severe cold area, which has high requirements for the shear bearing capacity of jacket leg of offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. A compound forming process of double-layer stainless steel pipe for primary circuit main pipeline of station is designed, which solves the problem of limited length of finished products in traditional forging or casting process, and meets the special requirements of complex working environment on pipeline performance. The three roll cross rolling forming process of double-layer casing with outer layer -n austenitic heat-resistant stainless steel and inner layer cr-ni martensitic heat-resistant stainless steel was simulated and optimized by using DEFORM-D finite element simulation software. The internal and external deformation, stress-strain field and temperature field of double-layer stainless steel pipe were analyzed and the optimal deformation parameter combination was obtained by orthogonal test. The simulation results show that in the process of three roll cross rolling, the large values of equivalent stress, equivalent strain and temperature are concentrated in the area between the outer tube and the roll, and the overall performance parameters of the outer tube are greater than those of the inner tube. The range analysis and variance analysis of orthogonal design test show that the optimal deformation parameter is rough rolling temperature deg; C. Feed angle & deg;, Roll speed: rmin. Objective to improve the existing connection mode of the braking system pipe system of railway freight cars, and accurately shape the end of the stainless steel pipe, so as to obtain the forged joint with better mechanical properties. According to the connection mode of the original pipe system and the plastic forming characteristics of steel pipe, a multi-step upsetting and extrusion process for the end of stainless steel pipe is proposed. The process is numerically simulated by DEFORM-D three-dimensional finite element simulation software, and the forging forming process is analyzedNuevitas,Shape, stress, temperature and metal flow of forgings and dies. Results the multi-step upsetting extrusion process under high temperature can make the end of steel pipe meet the forming requirements. Conclusion the plastic forming process of steel pipe end is feasible, which has important reference significance for the improvement of pipe connection mode of railway freight car braking system.Indicates that the chemical composition is represented by international chemical element symbols and national symbols, and the composition content is represented by letters: for example, China and Russia use fixed digit numbers to represent steel series or numbers; For example, the United States,NuevitasArgon arc welding of thin stainless steel pipe, Japan, series series and series; The serial number is composed of Latin letters and order, which only indicates the purpose.Stress corrosion cracking (SCC) refers to the cracking caused by the combined action of stress corrosion stress (mainly tensile stress) and corrosion of austenitic stainless steel Austenitic stainless steel is prone to stress corrosion in corrosive media containing chloride ions. When the Ni content reaches % - %, stainless steel coil, stainless steel belt and stainless steel pipe. Welcome to consult. The stress corrosion tendency of austenitic stainless steel is very large. Continue to increase the Ni content to ~ % and the stress corrosion tendency gradually decreases until it disappears.