The difference between square pipe and seamless steel pipe the main feature of seamless steel pipe is no welding joint and can withstand large pressure. The product can be very rough as cast or cold drawn parts.The disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave, and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.Naranjo,Among them, qb square tube is divided into process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral welded square pipe.Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid) and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.Kireka,Compared with other welding, square pipe welding has many advantages,NaranjoHot dip galvanized square pipe truss, mainly because of the exothermic reaction, the material only needs to be heated below the melting pointStage ( & mdash; )Stage ( & mdash; )

Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.There are many forms of heating furnace, but the ring heating furnace is mainly used. The heating furnace has an annular furnace bottom, which can rotate slowly, the blank is loaded along the diameter direction of the furnace bottom from the inlet, and can be heated and homogenized to the specified temperature when it is used at the outlet. The production process of seamless square tube is relatively slow, and the heating operation especially needs patience. Because if the heating operation is not standardized, cracks, folding and eccentricity on the inner or outer surface of the tube blank will only produce waste products and defective products.Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )where,For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient, it shall be welded to the fixed thickness, even if the steel pipe with another large opening can be made up at one time.

It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, and the density of steel is relatively good. After cold drawing and heating, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation,Naranjo22 galvanized square tube,NaranjoSpecification and size of galvanized flat pipe, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.Excellent quality,Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.Large fillet radius, insufficient blank holder area, easy to produce unstable wrinkles; If the fillet is too small, the resistance of the material into the die will increase in the deformation process, thus increasing the large tensile stress in the force transfer area, mostly mm and mm. Qb square tube is allowed to deliver short length and non fixed length products not less than mm, or in the form of interface tubeNaranjo,The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers the rolling of rolling groove often exceeds the standard.With the progress of the times and the faster and faster economic development, power plants the places where large-diameter seamless square tubes are used are becoming more and more popularMechanical engineering, agricultural and chemical machinery, glass curtain walls, automobile chassis, airports, boiler construction, highway railings, housing construction, pressure vessels, oil storage tanks, bridges, power station equipment, heavy transportation machinery and other welded structural parts with high load, etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes, seamless square tubes and qb square tubes.