Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality.The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.St. Peter lieuEvaluation of test results after the test, the bending deformation of the sample is qualified if there is no crack or crack. The squash test rating square pipe produced by square pipe factory has been widely used. Of course, the current situation is inseparable from the strict control of square pipe factory in technology, which makes the development of steel pipe make a lot of contributions. Let's look at the specific purpose of the lower tube.At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient, it shall be welded to the fixed thickness,St. Peter lieu6. What is the outer diameter of galvanized pipe, ground and sandblasted,St. Peter lieu20 galvanized pipe, and repair welding shall be adopted where there are cracks, even if the steel pipe with another large opening can be made up at one time.Mutare,Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.The floating mandrel mill is in its heydayBrinell hardness (HB), the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Low alloy steel is divided into q Mn Q, St-, etc.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Honesty and mutual benefit,The technology of floating mandrel and square tube is gradually mature.Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square tube, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant and the H-shaped steel is used as the load-bearing. Especially in recent years, a large number of small and medium-sized enterprises around the country have started to build spacious and bright plants. If the traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high, it will have a serious impact on the capital after operation. The plant built with qb square pipe, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, becoming the first choice for plant construction. Large diameter qb square pipe plant is introduced Shao measures for effective wrinkle of seamless square pipe: check the wrinkle state, even when the wrinkle around the part is determined to be less than the clamping force, and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, cold drawn tubes, tubes etc. Hot rolled seamless tubes are produced on the automatic precision tube precision tube rolling mill. The solid tube blank is cut into the required length by removing surface defects, centering on the end face of the perforated end of the tube blank, and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, it rotates and advances continuously under the action of roll and plug, A cavity is gradually formed inside the pipe blank, which is called the rough pipe, and then sent to the automatic pipe mill for continuous rolling. After the wall thickness is adjusted by the whole machine, and the diameter is determined by the sizing machine to meet the specification requirements. The continuous pipe mill is more advanced in producing hot-rolled seamless steel pipe. If you want to obtain seamless pipe with smaller size and better quality, Cold rolling and cold drawing must be adopted, that is, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move, This method can produce steel pipe with small diameter. In the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. We need to understand the various characteristics of steel pipes. However, in the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. The various characteristics of steel pipe need to be understood by everyone. However, due to the of steel pipe and other raw materials, the storage of steel pipe needs specific conditions.

Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).wholesaler, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionThe difference between qb square tube and QA is that there are fewer impurities s and P and better low-temperature impact performance. From the welding point of view, when the impurity elements in the base metal are less, it is good for welding hot crack.It is the process of drawing the die hole of the rolled metal blank (shape, pipe, product, etc.) into a section to reduce the length and increase. It is mostly used for cold processing.St. Peter lieu,Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust welding slag,St. Peter lieuCold rolled square tube, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.