SilmhantanTurkwan,

Stage equipment safety door. To prevent personnel from extending their heads, hands, and feet out of the shaft and objects from falling into the vertical shaft. Its vertical position should be closed, its cabin should be full of doors, and the height of the hoistway (hall door) should not be less than meters; The electric door opening and closing switches should be removed from the vertical and passenger compartment doors. In order to prevent accidents caused by vertical,SilmhantanSesena , and car roof doors not being closed.; Door interlocks should be installed on both the vertical and passenger compartment doors.Operating cost advantage and low failure rate: Due to the use of advanced hydraulic systems and good methods, the operating failure rate can be reduced to a low level.Silmhantan,Only after the operation of professional personnel can the suspension cage movement be restored.The pump body adopts an integrated pump station, which can also be selected according to customer requirements to meet customer ideal requirements.Koeln-Nippes,The quality of the standard section should comply with the product manual and specification requirements.Use floor doors and cage door devices on construction sites where conditions permit.The motor of the hydraulic guide rail lifting platform is set around the wellbore occupying a relatively small area, improving the utilization rate of the wellbore area.

With the continuous improvement of urbanization level in China, the number of high-rise buildings in urban areas has sharply increased, and the height of buildings has also continued to grow. This has created a demand for high-altitude lifting platform vehicles. Therefore in order to meet the needs of the domestic market and the public, efforts will inevitably be made to design and produce high-altitude lifting platform vehicles.Lower limit switch: In normal working state, before the suspension cage touches the buffer, the lower limit switch first acts.The use of a lifting platform as a tool for storing performance blankets, soft scenery,SilmhantanHanshan, etc. In some theaters, there is a soft scenery storage lifting platform located at an appropriate location on the stage for the storage of blankets, soft scenery, etc.system,Speed limiter. To prevent the driving speed from exceeding the normal speed. A speedometer should be installed (not required for floors below or including the second floor), which is an individual mechanism that is integrated with a safety clamp; The entrance and exit of the passenger compartment should be equipped with safety doors. Public places, family dormitories, andThe connection method and angle between the wall bracket and the building structure should comply with the requirements of the user manual.Before operating the construction electric elevator, routine inspections should be carried out according to regulations and inspection records should be filled out.

Human improper operation is the main factor causing malfunctions in scissor type electric elevators. When stacking goods, electric elevators should stack the goods neatly, which is better than stacking them in the center of the cargo stacking area of the cargo elevator to avoid imbalance between the two ends of the stacking area. Eventually, during the operation of the electric elevator, it may cause the electric elevator to lose balance. After the goods are stacked completely, ropes should be used to lock the goods, so that they are not afraid of the goods during the lifting process; Careless; Scattered downmarket,The setting of the cable guide frame should comply with the user manual and regulatory requirements.When a single steel wire rope is excessively stretched, the Electrical safety device shall stop the operation of the electric lift.Monthly maintenance and inspection of hydraulic lifting platform rollers, intermediate shafts and bearings, oil cylinder pin shafts and bearings, boom hinge shafts and bearings for wear. Add some oil to each part to extend the service life of the lifting platform bearings. The quality and level of hydraulic oil. The lifting platform should be raised throughout the entire process, and at this position, the hydraulic ground should be - millimeters higher than the bottom of the box. If the hydraulic oil becomes dark, sticky, or has foreign objects such as gravel, it should be replaced in a timely manner ( # hydraulic oil). Annual maintenance and inspection of all hydraulic pipelines and joints of the lifting platform. The pipeline must not be damaged, and the joints must not be loose. All joints must be tightened. Remove and disassemble the lowering valve of the lifting platform, blow out the plunger with compressed air, then install it and reinstall it. Drain and discard the hydraulic oil, tighten the joint remove the oil filter, clean it with compressed air, and then return it to the oil tank and connect the pipeline.Silmhantan,Electric elevators used in various places.Tank oil temperature protection: When the oil temperature in the tank exceeds the standard setting value